Metrohm 730 Sample Changer User Manual Page 97
- Page / 195
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4.4 Changer Commands
730 Sample Changer, Detailed Description
94
44.4 .4 Changer Changer CommandsCommands
4.4.1 Command Command ReferenceReference
The following commands are programmable within a sequence.
Most of them are also available in manual operation but may vary
partially in their operation or exhibit a limited parameter selection;
see page 46ff.
The following listing is valid for the programming of process se-
quences.
SAMPLE
7
SAMP LE
>start sequence
1 SAMPLE: = 1
=,+,– 1…999
Define first sample
The SAMPLE command can determine which rack position is to
be the position of the first sample (SAMPLE = X). This is stored as
a index variable. It may be modified for example, in a sample se-
quence (SAMPLE + X or SAMPLE – X), in order to control the
course of a sample series during processing.
The SAMPLE command does not have to be used for simple
applications. As a general rule the first sample of a series is as-
sumed to be in rack position 1 unless specified otherwise. There-
fore it is recommended not to place the special beakers in the first
rack positions; place them in the highest positions instead.
Before starting a sample series, the position of the first sample
can be defined with the <SAMPLE> key in manual operation, as
long as this has not been defined in the method itself.
If a certain sample beaker order is needed for each application of
a method, the position of the first sample can be defined in the
start sequence with 'SAMPLE = X' and this setting can be saved
with the corresponding method.
If the SAMPLE command is not executed during a sample se-
quence, the SAMPLE variable will be increased by 1 after every
processing of the sample sequence.
- 730 Sample Changer 1
- Table of Contents 2
- 1 Overview 4
- 730 Sample Changer, Overview 5
- 1.3 Instrument Description 6
- 1.3.2 Rear View 7
- 1.3.3 Sensors 8
- 11.3.3.5 .5 The Swing Head 9
- 2 Installation 10
- 2.3 Safety Considerations 12
- 2.4.3 Tubing Fixation 15
- 2.4.4 Magnetic Stirrers 15
- 2.4.5 Sample Racks 15
- 2.5 Integration 17
- 2.5.1 Remote Connections 18
- 683 Pump Unit 24
- Cable 6.2135.000 26
- Cable 6.2134.000 26
- 1 2 3 4 5 6 7 8 1 2 3 4 5 6 28
- 3 Introduction 30
- Basic Configuration 31
- >, <1> or <2> 32
- Rack Configuration 33
- The Method 34
- 3.2 Configuration 38
- 3.2.2 Rack Definition 40
- 3.2.3 Dosing Units 42
- 33.2.2.4 .4 RS232 Interface 43
- 3.3 Swing HeadSwing Head 45
- MOVE : sample <ENTER> 49
- MOVE : spec.1 <ENTER> 49
- MOVE : 5 <ENTER> 49
- LIFT : work <ENTER> 50
- LIFT : 150 mm <ENTER> 50
- 3.5 Methods and Sequences 52
- 3.5.3 Process Control 54
- 3.5.4 POWERUP Method 55
- 3.6 User Methods 56
- 4 Detailed Description 62
- 4.2 The Keyboard 63
- 44.2.2.2 .2 Data Entry 81
- 44.2.2.3 .3 Text Entry 82
- <HOME> 84
- 4.3.1 Configuration 85
- >auxiliaries 86
- 4.3.2 Parameters 90
- >manual stop 95
- >start sequence 97
- 1 SAMPLE: = 1 97
- =,+,– 1…999 97
- >sample sequence 104
- 11 WAIT 1 s 104
- 0…1…9999 s 104
- 12 ENDSEQ 104
- 4.5 Sample Racks 107
- 700 Dosino 112
- 4.7.1 Setting up the System 117
- 4.9.3 TriggersTriggers 130
- 4.9.5 Error Messages, Errors 131
- ∗ SAMPLE, STIR, DEF 134
- ∗ CTRL, WAIT, ENDSEQ 134
- Address of stirrer 1…4, ∗ 139
- Address of dosing unit 1…12 139
- Interface selection Rm, RS 140
- ∗, 14 Bit (1,0, or ∗) 144
- ∗ / ENDSEQ> 150
- ∗∗∗∗∗∗∗∗') 152
- 1...4, ∗ 154
- 1.1, 1.2, 1.∗, 2.1, 2.2, 2.∗ 154
- depending on object 156
- 4.11.2 Handshake 158
- Data output 159
- Data input 159
- 4.11.3 Pin Assignment 162
- View of soldered side of plug 163
- 5 AppendixAppendix 164
- 730 Sample Changer, Appendix 165
- 5.2 Technical Specifications 166
- 5.2.2 759 Swing Head 168
- 5.3.1 Servicing 169
- 5.4 Diagnosis 170
- 5.4.3 Working Memory (RAM) 172
- 5.4.4 Display 172
- 55.4.4.5 .5 Keyboard 173
- 5.4.6 Remote Interface 174
- 5.4.8 External Bus Interface 175
- 55.4.4.9 .9 Beeper 176
- 5.5 Initialize data memory 178
- 55.6 .6 Validation / GLP 180
- 5.7.1 Warranty 181
- EU Declaration of Conformity 183
- 759 Swing Head 184
- 5.8 AccessoriesAccessories 186
- Connecting Cables 190
- Sample racks and beakers 190
- Electrodes for Sample Changer 191
- Dosing Instruments 191
Related products and manuals for Equipment Metrohm 730 Sample Changer
Equipment Metrohm 776 Dosimat User Manual
(42 pages)
(42 pages)
Equipment Metrohm 787 KF Titrino User Manual
(83 pages)
(83 pages)
Equipment Metrohm tiamo 1.2 Manual User Manual
(842 pages)
(842 pages)
Equipment Metrohm 805 Dosimat User Manual
(34 pages)
(34 pages)
Equipment Metrohm 899 Coulometer User Manual
(178 pages)
(178 pages)
Equipment Metrohm 794 Basic Titrino User Manual
(198 pages)
(198 pages)
© 2020, manymanuals.com. All rights reserved. | 1.610 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals