Metrohm 730 Sample Changer User Manual Page 164
- Page / 195
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5.1 Error Messages
730 Sample Changer, Appendix
161
5 AppendixAppendix
5.1 Error Messages
When an error occurs the execution of the active command is in-
terrupted and an error message is displayed (display blinks). This
must be acknowledged with the <QUIT> key.
If an error occurs during processing of a sample series, the
changer will then be switched into the 'HOLD' state. After the
cause of the error has been rectified, the sample series can be
continued with the next command in the active sequence by
pressing the <START> key. If the error cannot be eliminated, the
method running can also be halted with <STOP>.
The list of possible error messages and their causes:
* battery low The battery for the permanent storage of user meth-
ods must be replaced.
* changer low power The power supply cannot deliver enough power for
the simultaneous operation of all components cur-
rently in use (stirrers, pumps, lifts).
* changer not ready The changer cannot execute the command chosen
because it is busy carrying out another action.
* changer overload Load or resistance too large to carry out the chosen
action.
* Dos## command not exec An error has occurred with the indicated dosing unit.
* Dos## ext. bus failure An unexpected error has occurred with an instrument
(Dosimat, Dosino) that is connected on the external
bus.
* Dos## no exchange unit There is no exchange unit mounted on the dosing
unit indicated.
* dos.unit ## missing The dosing unit chosen is not connected.
- 730 Sample Changer 1
- Table of Contents 2
- 1 Overview 4
- 730 Sample Changer, Overview 5
- 1.3 Instrument Description 6
- 1.3.2 Rear View 7
- 1.3.3 Sensors 8
- 11.3.3.5 .5 The Swing Head 9
- 2 Installation 10
- 2.3 Safety Considerations 12
- 2.4.3 Tubing Fixation 15
- 2.4.4 Magnetic Stirrers 15
- 2.4.5 Sample Racks 15
- 2.5 Integration 17
- 2.5.1 Remote Connections 18
- 683 Pump Unit 24
- Cable 6.2135.000 26
- Cable 6.2134.000 26
- 1 2 3 4 5 6 7 8 1 2 3 4 5 6 28
- 3 Introduction 30
- Basic Configuration 31
- >, <1> or <2> 32
- Rack Configuration 33
- The Method 34
- 3.2 Configuration 38
- 3.2.2 Rack Definition 40
- 3.2.3 Dosing Units 42
- 33.2.2.4 .4 RS232 Interface 43
- 3.3 Swing HeadSwing Head 45
- MOVE : sample <ENTER> 49
- MOVE : spec.1 <ENTER> 49
- MOVE : 5 <ENTER> 49
- LIFT : work <ENTER> 50
- LIFT : 150 mm <ENTER> 50
- 3.5 Methods and Sequences 52
- 3.5.3 Process Control 54
- 3.5.4 POWERUP Method 55
- 3.6 User Methods 56
- 4 Detailed Description 62
- 4.2 The Keyboard 63
- 44.2.2.2 .2 Data Entry 81
- 44.2.2.3 .3 Text Entry 82
- <HOME> 84
- 4.3.1 Configuration 85
- >auxiliaries 86
- 4.3.2 Parameters 90
- >manual stop 95
- >start sequence 97
- 1 SAMPLE: = 1 97
- =,+,– 1…999 97
- >sample sequence 104
- 11 WAIT 1 s 104
- 0…1…9999 s 104
- 12 ENDSEQ 104
- 4.5 Sample Racks 107
- 700 Dosino 112
- 4.7.1 Setting up the System 117
- 4.9.3 TriggersTriggers 130
- 4.9.5 Error Messages, Errors 131
- ∗ SAMPLE, STIR, DEF 134
- ∗ CTRL, WAIT, ENDSEQ 134
- Address of stirrer 1…4, ∗ 139
- Address of dosing unit 1…12 139
- Interface selection Rm, RS 140
- ∗, 14 Bit (1,0, or ∗) 144
- ∗ / ENDSEQ> 150
- ∗∗∗∗∗∗∗∗') 152
- 1...4, ∗ 154
- 1.1, 1.2, 1.∗, 2.1, 2.2, 2.∗ 154
- depending on object 156
- 4.11.2 Handshake 158
- Data output 159
- Data input 159
- 4.11.3 Pin Assignment 162
- View of soldered side of plug 163
- 5 AppendixAppendix 164
- 730 Sample Changer, Appendix 165
- 5.2 Technical Specifications 166
- 5.2.2 759 Swing Head 168
- 5.3.1 Servicing 169
- 5.4 Diagnosis 170
- 5.4.3 Working Memory (RAM) 172
- 5.4.4 Display 172
- 55.4.4.5 .5 Keyboard 173
- 5.4.6 Remote Interface 174
- 5.4.8 External Bus Interface 175
- 55.4.4.9 .9 Beeper 176
- 5.5 Initialize data memory 178
- 55.6 .6 Validation / GLP 180
- 5.7.1 Warranty 181
- EU Declaration of Conformity 183
- 759 Swing Head 184
- 5.8 AccessoriesAccessories 186
- Connecting Cables 190
- Sample racks and beakers 190
- Electrodes for Sample Changer 191
- Dosing Instruments 191
Related products and manuals for Equipment Metrohm 730 Sample Changer
Equipment Metrohm 776 Dosimat User Manual
(42 pages)
(42 pages)
Equipment Metrohm 787 KF Titrino User Manual
(83 pages)
(83 pages)
Equipment Metrohm tiamo 1.2 Manual User Manual
(842 pages)
(842 pages)
Equipment Metrohm 805 Dosimat User Manual
(34 pages)
(34 pages)
Equipment Metrohm 899 Coulometer User Manual
(178 pages)
(178 pages)
Equipment Metrohm 794 Basic Titrino User Manual
(198 pages)
(198 pages)
© 2020, manymanuals.com. All rights reserved. | 3.014 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals