Metrohm tiamo 2.1 (ProcessLab) User Manual

tiamo 2.1 (ProcessLab)Online Help8.101.8016EN

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭VIII￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.7 Subwindow Sensors ...

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭84￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Properties RunwindowSets properties for the tab Single determination or D

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭984￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing rateSpeed at which the volume increments are added. The maximum dosingrate d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭985Measuring intervalTime interval for entering a measuring point in the measuring point l

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭986￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando: 808, 809, 835, 836, 857, 904, 905, 906, 907pH/Ion - Meter: 867Robotic Tit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭987Identifi-cationDescription.ENPElectrode zero point calculated from the calibration.ETEE

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭988￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)not definedIn this case, the device name must be assigned by the user at the start

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭989NoteIf an existing solution is selected as the solution to be added then theConcentrati

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭990￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)StirrerStirrerSelection of the stirrer.Selection1 | 2 | 3 | 4 | offDefault value1of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭991Stop volumeVolume of auxiliary solution (e.g. buffer) that is to be added to the sample

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭992￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The parameters for the measuring procedure can be defined on this tab.Measurement w

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭993Switch off stirrer during measurementSwitch off stirrer during measurementon | off (Def

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭85Change layoutChanges layout of the loaded workplace view (see Chapter 3.1.7.2, page 8

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭994￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The calibration can be carried out with both manual and automatic solutionchanges w

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭995￭ CAL MEAS ConcMeasurement of standards for the calibration of ion-selective electrodes

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭996￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)method run, a request for specifying the next the buffer or standard is dis-played

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭997The request for changing the buffer or standard must be deactivated inthe command CAL L

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭998￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe formula editor is opened with a right click in the input field.5.6.5.4 CAL

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭999Identifi-cationDescription.SLOElectrode slope calculated from the calibration5.6.5.4.2

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1000￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe automatic buffer recognition is deactivated for the buffer type Spe-cial a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1001Temp. (°C) Met4 Met7 Met9 pH 4.00 pH 7.00 pH 9.0010 3.99 7.06 9.1315 3.99 7.04 9.0820

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1002￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Temp. (°C) NIST1 NIST4 NIST7 NIST9 NIST13 pH 1 pH 4 pH 7 pH 9 pH 1335 1.691 4.025

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1003Temp. (°C) DIN1 DIN3 DIN4 DIN7 DIN9 DIN12 pH 1 pH 3 pH 4 pH 7 pH 9 pH 1260 1.11 3.04

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭86￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The original view of all subwindows is restored when the button is clic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1004￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Temp. (°C) Fis2 Fis4 Fis7 Fis10 pH 2 pH 4 pH 7 pH 1085 - 4.18 7.06 9.6190 - 4.21

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1005Mettler-ToledoTemp. (°C) MT2 MT4 MT7 MT9 MT11 pH 2 pH 4 pH 7 pH 9 pH 110 2.03 4.01 7.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1006￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Temp. (°C) Mer2 Mer4 Mer7 Mer9 Mer12 pH 2 pH 4 pH 7 pH 9 pH 1220 2.00 4.00 7.00 9

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1007Temp. (°C) MerC4.01 MerC7.00 MerC9.00 MerC10.00 pH 4.01 pH 7.00 pH 9.00 pH 10.0045 4.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1008￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Temp. (°C) Bec4 Bec7 Bec10 pH 4 pH 7 pH 1070 4.12 6.99 -75 4.14 7.00 -80 4.16 7.0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1009Temp. (°C) Rad4.01 Rad7.00 Rad9.18 pH 4.01 pH 7 pH 9.1895 4.240 - -BakerTemp. (°C) Ba

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1010￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Temp. (°C) Ham4.01 Ham7.00 Ham9.21 Ham10.01 pH 4.01 pH 7.00 pH 9.21 pH10.015 4.01

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1011Temp. (°C) Pre4 Pre7 Pre9 pH 4.00 pH 7.00 pH 9.0030 4.00 6.99 8.9635 4.01 6.98 8.9340

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1012￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command CAL MEAS pH are configured on thefollowin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1013Identifica-tionDescription.MTE Temperature measurement with sensor; 1 = on, 0 =off).NM

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭87Subwindow Method￭ Zoom￭ Modify parameters live￭ Interrupt commandsSubwindow Report￭ S

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1014￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 867Selection1 | 2Default value1855Selection1Default value1TitrinoSelecti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1015offMeans that no stirrer will be used.Stirring rateSetting the stirring rate. The alge

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1016￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Min. waiting timeThe measured value is not accepted until the minimum waiting time

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1017Range-20.0 ... 150.0 °CDefault value25.0 °C5.6.5.6 CAL LOOP Conc5.6.5.6.1 CAL LOOP C

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1018￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.5.6.2 CAL LOOP Conc - PropertiesDialog window: Method ▶ CAL LOOP Conc ▶ Prope

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1019DevicesThis command can be executed with the following devices:Titrando: 808, 809, 835

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1020￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription.ITEInitial temperature (temperature before start condit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1021If the option not defined is selected as Device name, any device types ordevice groups

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1022￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selection1 | 2 | 3 | 4 | offDefault value1offMeans that no stirrer will be used.St

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1023Max. waiting timeIf the signal drift has not yet been reached, then the measured value

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭88￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Automatic loadThe standard procedure is that the view saved when the prog

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1024￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command CAL Cond are configured on the follow-ing

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1025Identifica-tionDescription.LP.TEMTemperature for the last measuring point of the measu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1026￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SensorSensorSelection of a conductivity sensor from the conductivity sensors avail

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1027Switch off automaticallyon | off (Default value: off)If this option is enabled, the st

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1028￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteA constant measured value is often only achieved after a certain time, asmixin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1029856Range0.1 ... 999999.0 sDefault value2.0 sMeasurement without drift controlIf the op

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1030￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionInput | Request | TemplateDefault valueInputInputIf this option is select

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1031Name standardList box with conductivity standards. The data of one of these standards

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1032￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)AppearanceThe command has the following appearance:ParametersThe parameters for th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1033Identification Description.CP{#}.MEAMeasured wavelength of the calibration point in nm

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭89Move the selected subwindow upward (modifies sequence).Move the selected subwindow do

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1034￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.5.9.3 CAL Spec - Measuring parametersTab: Method ▶ CAL Spec ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1035[Properties]Opens the dialog window Calibration wavelength # to edit the valuesselecte

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1036￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando: 808, 809, 835, 836, 841, 842, 851, 852, 857, 888, 890, 901,902, 904, 905

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1037Identifica-tionDescription.TITERTiter value of the solution used for the command.VOLCu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1038￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 846, 856, 867Selection1 | 2 | 3 | 4Default value1778, 789, 814, 815, 855

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1039Titrando, 846, 856, 867Selection1 | 2 | 3 | 4Default value2814, 815, 855, 864, 874Sele

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1040￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate ch

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1041Dosing rateThe rate at which the volume is dosed. The maximum dosing rate dependson th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1042￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Fill automatically at starton | off (Default value: on)If this option is enabled,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1043CommandsDepending on the measured value, one of the following two DOS com-mands can be

3.2 Workplaces￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭90￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.1.7.5 Rename viewDialog window:Workplace / Database / Configura-tion ▶ View ▶ R

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1044￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The time defined as Dosing time corresponds to the net dosing time t1+t2,i.e. the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1045Flow rate of a single dosing deviceThe cylinder volume and the filling time of the exc

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1046￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Cylinder volume Filling time in s max. 100 mL/min 50 mL/min 10 mL/min1 mL 24/---

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1047AnyEither one of the two sizes.Limit exceedingSelects the exceeded limit for which a t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1048￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command DOS pH are configured in the following5 t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1049Identifica-tionDescription.IMEInitial measured value (measured value before start con-

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1050￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.6.3.4.2 DOS pH - General/HardwareTab: Method ▶ DOS pH ▶ Properties... ▶ Gener

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1051855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectionin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1052￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SolutionInput of a solution name or selection of a solution from the solutions def

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1053SensorSelection of a sensor of type pH electrode from the list of sensors availablein

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭91NameEntry of a name for the selected workplace or selection from the list of the10 na

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1054￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Switch off automaticallyon | off (Default value: on)If this option is enabled, the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1055Titrando, 855Range0.01 ... 166.00 mL/minDefault valuemaximum mL/minTitrinoRange0.01 ..

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1056￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.1 ... 999999 sDefault value5.0 sTitrinoRange1 ... 999999 sDefa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1057offMeans that no stop will take place.Filling rateRate at which the dosing cylinder is

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1058￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range-20.000 ... 20.000 Default value-20.000 TitrinoRange-20.00 ... 2

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1059Stop determinationThe running DOS command is quit, then the exit track (if present) is

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1060￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Upper limitUpper limit of the temperature. When the temperature exceeds this value

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1061Track call on limit exceedingIn this table, which cannot be edited directly, max. 20 e

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1062￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Delete]Deletes the calculated measured value selected in the table.Additional ext

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1063ParametersThe parameters for the command DOS U are configured in the following 5tabs:￭

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭92￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.2.3.2 Displaying single workplacesMenu item: Workplace ▶ View ▶ UnsplitIn th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1064￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription.FIN Command status; 1 = Command has been ended atleast

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1065Identifica-tionDescription.VOLDosed volume5.6.6.3.5.2 DOS U - General/HardwareTab: Me

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1066￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selecti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1067SolutionInput of a solution name or selection of a solution from the solutions defined

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1068￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SensorSelection of a sensor of type pH electrode, metal electrode, pH elec-trode o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1069Switch off automaticallyon | off (Default value: on)If this option is enabled, the sti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1070￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.01 ... 166.00 mL/minDefault valuemaximum mL/minTitrinoRange0.0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1071Titrando, 855Range0.1 ... 999999 sDefault value5.0 sTitrinoRange1 ... 999999 sDefault

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1072￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)device, it will automatically be reduced during dosing to the largest possiblevalu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1073Lower hysteresisLower hysteresis of the measured value. If the measured value exceeds

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭93NameName of the sample table.SavedDate and time when the sample table was saved.Saved

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1074￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Wait for [Continue]Reagent dosing in the current DOS command is interrupted and a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1075Titrando, 855Range-20.0 ... 150.0 °CDefault value150.0 °CTitrinoRange-170.0 ... 500.0

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1076￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Track call on limit exceedingIn this table, which cannot be edited directly, a max

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1077[Delete]Deletes the calculated measured value selected in the table.Additional externa

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1078￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)AppearanceThe command has the following appearance:ParametersThe parameters for th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1079DeviceDevice nameSelection of a device from those available in the device table. The o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1080￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)of the working life, the validity of the titer and the GLP test interval for these

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1081Exchange positionWith this function the cylinder is filled via the given port first.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1082￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DosingRange0.00000 ... 99999.9 mLDefault value10.0000 mLAspirateRange0.00000 ... 5

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1083ParametersThe parameters for the command PREP are configured in the followingdialog wi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭IX7.5.4 Properties - MSB # ...

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭94￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)IncrementAutomatically increments selected lines.FillingAutomatically fills sel

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1084￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device typeDisplay or selection of the device type. If a device is selected under

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1085Selection'Solution name' | not definedDefault valuenot definednot definedNo

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1086￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY;

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1087Dosing deviceDosing deviceSelection of the dosing device (Dosinos only) to be emptied.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1088￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.7 Automation commands5.6.7.1 Automation commands - OverviewMenu item: Method

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1089￭ MOVE - PropertiesCommand variablesThe following command variables are generated in t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1090￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device typeDisplay or selection of the device type. If a device is selected under

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1091Move = Rack positionRange1 ... 999 Default value1 Move = Special beaker (for 778, 789,

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1092￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop determination and seriesThe determination as well as the series are stopped.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1093AppearanceThe command has the following appearance:ParametersThe parameters for the co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭95Unmark linesRemoves the line marking for the selected lines.Set lines inexecutableSet

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1094￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selection'Device name' | not definedDefault valuenot definednot definedI

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1095Range1 ... 4 Default value1 Swing angleAngle by which the robotic arm is to be swung r

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1096￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY;

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1097TargetTowerSelection of the tower of the Sample Processor for moving to the requiredli

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1098￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)778, 789, 814, 815, 855, 864, 874Range5 ... 25 mm/sDefault value25 mm/s730Range3 .

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1099Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; inva

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1100￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selection1 | 2Default value1Pump(s)Selection of the pump that is to be actuated. T

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1101Coulometer: 756, 831Dosing Interface: 846pH/Ion - Meter: 867Sample Processor: 730, 778

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1102￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DeviceDevice nameSelection of a device from those available in the device table. T

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1103Stirrer typeDisplay of the stirrer type. Unknown is displayed either with devices unab

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭96￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIf a method is changed and saved in the method editor or during reproc-essi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1104￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Period of operationThe stirrer can be switched on for a particular period.Range0 .

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11055.6.7.7.2 RACK - PropertiesDialog window: Method ▶ RACK ▶ Properties... ▶ RACK - &apo

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1106￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.7.8 HEATER5.6.7.8.1 HEATER - OverviewDialog window: Method ▶ HEATER ▶ Proper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1107DeviceDevice nameSelection of a device from those available in the device table. The o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1108￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Off causes heating at the maximum possible heating rate (see device man-ual).Range

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1109AppearanceThe command has the following appearance:ParametersThe parameters for the co

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1110￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device typeDisplay or selection of the device type. If a device is selected under

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1111Gas flowSelectionSwitch on | Switch offDefault valueSwitch onSwitch onSwitches on the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1112￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Result parametersThe parameters for the individual results on the results table ar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1113Identifica-tionDescription.OVF Limit value violation for result; 1 = limit exceeded, 0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭97NoteIf a value is entered or imported into this field, then in addition the timeof th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1114￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Result nameName of the result.FormulaCalculation formula of the result.DeviceResul

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11155.6.8.2.4 CALC - Formula assistantDialog window Method ▶ CALC ▶ [New] ▶ New resultat

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1116￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Select result variableAll of the result variables of the formula template will be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1117DeviceUnit of the result for the output (text only). The unit can be used in furtherca

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1118￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Statisticson | off (Default value: on)Mean value, absolute and relative standard d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1119into the text field (see Chapter 2.5.2, page 79). The formula editor can alsobe called

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1120￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop determinationThe determination is stopped and the next determination of the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1121Save result as titeron | off (Default value: off)If this option is enabled, then the r

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1122￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.8.2.6.2 Save result templateDialog window: Method ▶ CALC ▶ Properties... ▶ [N

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1123AppearanceThe command has the following appearance:ParametersThe parameters for the co

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭98￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Jump to the next line in the sample table. If the end of the table has beenreac

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1124￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DatabaseName of the database in which the determination data is stored.[New]Opens

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1125Command variablesThe following command variables are generated in the method run by th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1126￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)PDF fileon | off (Default value: off)The report is stored as PDF file in the direc

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1127Identifi-cationDescription.FIN Command status; 1 = Command has been ended atleast once

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1128￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.9.2 CTRL5.6.9.2.1 CTRL - OverviewDialog window: Method ▶ CTRL ▶ Properties..

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1129Identifi-cationDescription.FIN Command status; 1 = Command has ended at leastonce, 0,

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1130￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Set linesOutput signalInput of the binary pattern for the output signal or selecti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1131NoteFor Titrinos with 3 output lines: only the first 3 characters are used.5.6.9.3 SC

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1132￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY;

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1133Titrando, 856, 867, 814, 815, 855, 864, 874Selection1 | 2 | 3 | 4Default value1Scan li

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭993.3.1.6 Importing sample dataDialog window: Workplace ▶ Sample table / Determination

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1134￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.9.4 SEND5.6.9.4.1 SEND - OverviewDialog window: Method ▶ SEND ▶ Properties..

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1135NoteA maximum of 10 event messages can be entered.[New]Opens the dialog window Send ev

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1136￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Recipi-entSelec-tionEventmes-sageSignificanceSystem-HoldHold determination (all tr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1137Recipi-entSelec-tionEventmes-sageSignificanceCom-mandSET, KFT,KFCStartTitra-tionStart

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1138￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ RECEIVE - PropertiesCommand variablesThe following command variables are generat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1139[Properties]Opens the dialog window Wait for event/status to edit the event messagesel

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1140￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Event/StatusType Significance Com-mandsStartEvent Command has been started. AllEnd

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1141ParametersThe parameters for the command TRANSFER are configured in the fol-lowing dia

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1142￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device typeDisplay or selection of the device type. If a device is selected under

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1143Selectionmin | sDefault values5.6.9.6.3 TRANSFER - Transfer commandDialog window: Met

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭100￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)File typePrescribed format *.csv.Selection[*.csv]Default value[*.csv][Save]The

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1144￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteAll ASCII characters can be entered with its two-digit hex code after back-sla

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1145[abc]OR function for single charac-tersreceive a or b or c[a-z0-9]one character in the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1146￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command WEIGH are configured in the followingdial

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1147Device typeDisplay or selection of the device type. If a device is selected under Devi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1148￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.10 Miscellaneous commands5.6.10.1 Miscellaneous commands - OverviewMenu item

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1149Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; inva

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1150￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteText is selected as type in the default settings for the sample identifica-tio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11515.6.10.2.3 REQUEST - Sample data requestDialog window: Workplace ▶ [START] ▶ Sample d

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1152￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteSample data can be loaded directly from a balance or a barcodereader. The data

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1153Command variablesThe following command variables are generated in the method run by th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭101Sample table test finished with errorsThis display appears if an error has occurred

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1154￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window Call to edit the call selected in the table (s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1155A LOOP command just inserted has an arrow on the left-hand side withwhich a loop can b

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1156￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1157The LOOP command is at the end of the loop for Repeat loops. As soonas one stop criter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1158￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.10.4.2 LOOP - PropertiesDialog window: Method ▶ LOOP ▶ Properties... ▶ LOOP -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1159The input field contains the expression for the condition(s) which can becreated or ed

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1160￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.10.5.2 WAIT - PropertiesDialog window: Method ▶ WAIT ▶ Properties... ▶ WAIT -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1161Record messageon | off (Default value: off)If this option is enabled, the message defi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1162￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY;

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1163PasteUse this context-sensitive menu item to paste the commands at the end of thetable

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭102￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Save]Save the sample table under the desired name.3.3.1.10 Print sample tabl

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1164￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Once the command has expired, the statuses and the set values of all of thedigital

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1165Selection'Device name' | not definedDefault valuenot definednot definedIn th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1166￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)FunctionsMoves the selected line up.Moves the selected line down.[New]Opens the di

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1167Start delayWaiting time in seconds or minutes before the initiated action is started.R

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1168￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ >0: For 100% stirrer output (Parameter 1 = 100), pulse duration in 10msExampl

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1169Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; inva

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1170￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.11.3.3 DIGITAL IN - Stop criteriaTab: Method ▶ DIGITAL IN ▶ Stop criteriaComm

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11715.6.11.4 ANALOG OUT5.6.11.4.1 ANALOG OUT - OverviewDialog window: Method ▶ ANALOG OU

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1172￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.[VAL] Value of the command variables (optional, i.e. Co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1173If a command block originates from a different device, the Port descrip-tion of which

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭103Operating elementsNoteThis parameter group is visible only if the dialog window abov

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1174￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Mapping range and unit of the value are defined in the configuration of theanalog

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1175Identifi-cationDescription.FIN Command status; 1 = Command has ended at leastonce, 0,

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1176￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop criteriaDefinition of possible stop criteria. The first stop criterion to be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1177Mode of operationStepping motors can be actuated with time controls.ParametersThe para

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1178￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)not definedIn this case, the device name must be assigned by the user at the start

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1179[New]Opens the dialog window Stepping motor # in order to edit a new line(see Chapter

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1180￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DistanceDistance to be moved to.Visible only in cases of stepping motors where Typ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1181Selections | minDefault values5.6.11.7 PORT5.6.11.7.1 PORT - OverviewDialog window:

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1182￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.11.7.2 PORT - PropertiesDialog window Method ▶ PORT ▶ Properties... ▶ PORT -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1183Selectionascending | descending | automatic | not overDefault valueautomaticascendingT

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭X￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.11.8 External position ...

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭104￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample dataNoteThe names defined here will be used only for the column heading

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1184￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6 Configuration6.1 Configuration - General6.1.1 Configuration -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11856.1.3 Configuration - Menu bar6.1.3.1 Configuration - Main menusProgram part:

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1186￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Load view...Load a saved configuration view (see Chapter 3.1.7.3, p

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11876.1.4 Configuration - ToolbarProgram part: ConfigurationChange layout...Modify

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1188￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)PresentationThe subwindows can be enlarged or made smaller to suit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1189Backup/Restore configuration data￭ Backup configuration data automatically￭ Sav

6.1 Configuration - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1190￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Automatic loadThe standard procedure is that the view saved when th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1191Move the selected subwindow upward (modifies sequence).Move the selected subwin

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1192￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.1.7.5 Rename viewDialog window:Workplace / Database / Configura-tion ▶ Vi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1193StructureThe dialog window User administration is divided into two parts, the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭105Input50 charactersDefault valueSample sizeUniton | off (Default value: on)Enable/dis

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1194￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DescriptionDescription of the user group.Input256 characters[Rename group]Re

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1195deactivated. If a subitem, e.g. the menu Tools, is deactivated in the con-figur

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1196￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Delete signatures Level 2If this check box is enabled then users in this use

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1197Executable methodsOnly methods with Signature Level 2If this check box is enabl

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1198￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Group nameName of new group.Input24 charactersWith [OK] a new group is gener

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1199NoteIt is only possible to delete a user group when the group no longer con-tai

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1200￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)removedUsers with the status removed can no longer log in. If the status of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1201UserShort name of new user that must be used to log in at program start. Aftert

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1202￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Security settings can be exported and imported. This means that these set-ti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1203as his/her user name. If this check box is disabled, then all subsequentparamet

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭106￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Copy automatically into next lineMethodon | off (Default value: on)If this opt

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1204￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteWith Windows 2000, proceed as follows for password monitoring byWindows:

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1205Selectionon | offDefault valueoffFDA default: offNoteIf the automatic logout is

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1206￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe immediate termination of all determinations on all activated work-pl

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1207Range1 ... 999 DaysDefault value365 DaysFDA default: 365 days6.2.2.3 Test logi

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1208￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ModificationsComment on modification of methodsIf this check box is enabled

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1209Selectionon | offDefault valueoffFDA default: onRange1 ... 60 minDefault value1

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1210￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Adds a new reason.[Edit]Edits the selected reason.[Delete]Deletes the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1211Authenticationon | off (Default value: off)Check box for activating the authent

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1212￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ LicensesList of installed licenses with number of clients. This tab is onl

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1213NoteIf the backup directory is on a network drive the saving date should beadde

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1073.3.2.4 Properties - Process Dialog window:Workplace ▶ Tools ▶ Sample table ▶ New…

6.2 Administration￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1214￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.2.3.3 ClientsTab: Configuration ▶ Tools ▶ Program administration ▶ Client

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1215NoteIn client/server systems this tab is only visible on the server and only fo

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1216￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Common variableson | off (Default value: on)Exports configuration data f

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1217Buffer dataon | off (Default value: on)Exports configuration data for custom bu

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1218￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Deviceson | off (Default value: on)Imports configuration data for device

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1219 Result templateson | off (Default value: on)Imports saved result templates (se

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1220￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.3.2 Backup/Restore6.3.2.1 Backup configuration data automatically Di

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12216.3.2.2 Backup configuration data manually Dialog window: Backup ▶ Configurati

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1222￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ tiamo multiMake sure that tiamo is closed on all clients connected to

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1223[Start]Starts the recovery of the configuration database. After the start, a pr

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭108￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop series ([Stop])If this option is selected, then the series is stopped bef

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1224￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteFor your own calibration buffers you should enter the pH values for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12251 = Line active and* = Any line status.SelectionBit-pattern with 8 characters (

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1226￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Creating new template or editing templateWith <New> or <Edit>

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1227Start Dos1 *****p********Starts Dosimat 1 (Titrino via "acti-vate")St

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1228￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input1000 charactersMeasured observational pairsTable with the value pai

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1229[New]Generates a new template. The window Edit E-mail template opens, inwhich a

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1230￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range1 ... 1 … 65536 Default value25 Authenticationon | off (Default val

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12316.3.4.2 Options - GeneralTab: Configuration ▶ Tools ▶ Options ▶ Options ▶ Gene

6.3 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1232￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)then any alterations that may have been made to the view will not be sav

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12336.4 Audit Trail6.4.1 Audit Trail - General6.4.1.1 Audit Trail - Definition P

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭109Always accept dataIf this option is selected, then the data sent from the balance is

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1234￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.4.1.3 Audit Trail - Menu bar6.4.1.3.1 Audit Trail - Main menus Program wind

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1235Special filter...Defines and uses special filter (see Chapter 6.4.2.3.4.1, page

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1236￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionAll entries | Quick filter | Temporary filter | FilternameDefault valu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12376.4.1.7 Audit Trail - Functions Program window: Configuration ▶ Tools ▶ Audit

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1238￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DateDate, time and time zone of the action.UserShort name of the logged-in user

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1239￭ Filter Audit Trail￭ Update Audit Trail￭ Export Audit Trail￭ Archive Audit Tra

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1240￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Remove filter6.4.2.3.2 Audit Trail - Last filter Menu item: Audit Trail ▶ Fi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1241[Save filter]Opens the dialog window Save filter in which the filter criteria e

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1242￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.4.2.3.4.2 Special filter - Editing filter criterionDialog window: Audit Trai

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1243NoteIf for the column Date, the Operator Today is selected then filteringwill b

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭110￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Import from fileon | off (Default value: off)If this option is enabled, then e

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1244￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Filter nameName under which the special filter is to be saved.Input50 character

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1245SelectionSelectionAll records | Selected recordsDefault valueAll recordsAll rec

6.4 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1246￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteArchiving Audit Trail entries is identical to exporting them, i.e. the Audi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1247Input24 characters6.4.2.8 Print Audit Trail Dialog window: Audit Trail ▶ File

6.5 Subwindow Devices￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1248￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Maximum numberMaximum number of entries allowed in the Audit Trail table.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1249Peripheral devices of USB devicesPeripheral devices connected to USB devices (e

6.5 Subwindow Devices￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1250￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe device status is permanently monitored and updated for USB device

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1251FunctionsThe menu [Edit] beneath the device table contains the following menuit

6.5 Subwindow Devices￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1252￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.5.2.4 Devices - Column displayDialog window: Configuration ▶ Devices ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1253Table contentsThe following information concerning the ignored devices is shown

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭111Entering a comment on the sample table.Comment on sample tableEntering a comment on

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1254￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ 756/831 Coulometer￭ 712 Conductometer￭ 856 Conductometer￭ 86

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1255Non-intelligent exchange units (EU) and dosing units (DU)Non-intelligent exchan

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1256￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)With menu item [Edit] ▶ Column display... further columns from

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1257NoteSolutions in intelligent 806 Exchange Units (IEU) or 807 Dosing Units (IDU)

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1258￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.6.2.5 Print list of solutionsDialog window: Configuration ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12596.6.3.2 Properties - SolutionTab: Configuration ▶ Titrants/Solutions ▶ [Edit]

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1260￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 999 DaysDefault value999 DaysExpiry dateExpiry date

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12616.6.3.3 Properties - TiterTab: Configuration ▶ Titrants/solutions ▶ Properties

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1262￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Rel. standard dev. (s rel)Relative standard deviation for the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1263SelectionRecord message | Display message | Stop deter-minationDefault valueDis

3.3 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭112￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)CopyCopies the selected sample table(s) (see Chapter 3.3.3.3, page 112).Delete

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1264￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThis parameter is not saved on the data chip of intelligen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭12656.6.3.5 Titer history Limit valuesDialog window: Configuration ▶ Titrants/solu

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1266￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.6.3.6 Properties - Exchange unitTab: Configuration ▶ Titran

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1267IEUInput8 charactersDefault value'empty'EUInput10 charactersDefault v

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1268￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Maximum Dosing/Filling rate for exchange unit as a function of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1269LengthLength of the tubing connecting the cock to the cylinder.Range0.0 ... 999

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1270￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.6.3.7 Properties - Dosing unitTab:Configuration ▶ Titrants/

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1271Input24 charactersDefault value'empty'Serial numberSerial number of d

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1272￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing rate Dosing port 2Speed at which dosing is to be carrie

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1273Tubing parametersDefines the length and diameter of the tubing connected to the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1133.3.3.6 Importing sample tableDialog window: Workplace ▶ Tools ▶ Sample table ▶ Man

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1274￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0.0 ... 999.9 cmDefault value0.0 cmDiameterDiameter of tu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1275Range0.0 ... 9.9 mmDefault value2.0 mm Port assignment of dosing unit:Valve dis

6.6 Subwindow Titrants/Solutions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1276￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Comment GLP testComment on GLP test.Input1000 charactersMonito

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1277Acoustic signalon | off (Default value: off)If this option is enabled, an acous

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1278￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Standard sensorsThe sensor table contains the following sensors as standa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1279pH(0)/E(0)Electrode zero point of the sensor.Next calibrationDate on which the

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1280￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.7.2.2 Sensors - Column displayDialog window: Configuration ▶ Sensors ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1281IonSelectionAg | BF4 | Br | Ca | Cd | Cl | CN | Cu | F | I | K | Na |NH4 | NO2

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1282￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[OK]The sensor table is produced in the required format as a PDF file and

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1283Order numberOrder number of the sensor (read-only for intelligent sensors).Inpu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭XI7.18.2 Barcode reader - Overview ...

3.4 Sample assignment table￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭114￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Method, the table can be sorted according to the selected column in

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1284￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sensor monitoringon | off (Default value: off)If this option is switched

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1285SelectionRecord message | Display message | Stop deter-minationDefault valueDis

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1286￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Specific calibration data for ISE electrodesSlopeSlope of the ISE electro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1287Shared calibration dataCalibration temperatureTemperature during the calibratio

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1288￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe days are monitored, e.g. the calibration becomes invalid when the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1289SelectionRecord message | Display message | Stop deter-minationDefault valueDis

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1290￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)for ISE (-1)Range-2.147E+9 ... 2.147E+9 mVDefault value-61.0 mVfor ISE (+

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1291for ISE (-2)Range-2.147E+9 ... 2.147E+9 mVDefault value-25.0 mVfor ISE (+3)Rang

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1292￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)message appears and you can choose whether you will nevertheless acceptth

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1293pH electrodes, the Slope and the pH(0) are displayed, for ISE electrodes theSlo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭115Open the dialog window Open method for the extended method selection.If a method is

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1294￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Black, when the values have been entered manually.If limits have been d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1295Warning limits for slope (only for pH and ISE electrodes)on | off (Default valu

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1296￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Upper limitUpper warning limit for the slope.for pH electrodeRange-2.147E

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1297Lower limitLower intervention limit for the slope.for pH electrodeRange-2.147E+

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1298￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)for ISE (+1)Range-2.147E+9 ... 2.147E+9 mVDefault value62.4 mVfor ISE (-1

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1299Range-2.147E+9 ... 2.147E+9 Default value7.500 Intervention limits for pH(0) (o

6.7 Subwindow Sensors￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1300￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range-2.147E+9 ... 2.147E+9 mVDefault value-30 mVUpper limitUpper interve

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13016.8 Common variables subwindow6.8.1 Configuration - Common variables Subwindo

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1302￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)UnitUnit of the common variables.Assignment dateDate of the last

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1303New…Adds new common variable manually (see Chapter 6.8.2.2, page 1303).DeleteDe

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭116￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Add new text template (see Chapter 3.5.2, page 116).[Properties]Edit sele

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1304￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Removes the selected column from the table.Modifies the sequence

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13056.8.3.2 Properties - Common variableTab: Configuration ▶ Common variables ▶ [E

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1306￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input256 charactersAssignment dateDate and time at which the las

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1307Message by E-mailon | off (Default value: off)The message is additionally sent

6.8 Common variables subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1308￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ValueThe values are shown in the following colors:￭ Blue, if the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13096.8.3.4 History - LimitsDialog window: Configuration ▶ Common variables ▶ [Edi

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1310￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.9 Sample solutions (TC conductivity) subwin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1311c0 ... c4Coefficients of the Chebyshev polynomial for the calculation of the fu

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1312￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)If the contents of a field is larger than the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1313Removes the selected column from the table.Modifies the sequence of displayed c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1173.6.2 Run testMenu item: Workplace ▶ Tools ▶ Run testNoteIn contrast to the Sample

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1314￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)6.9.3.2 Properties - GeneralTab: Configuratio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1315c0 ... c4Coefficients of the Chebyshev polynomial for the calculation of the fu

6.9 Sample solutions (TC conductivity) subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1316￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionDate selectionMessageThe message opti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13176.10 Rack data subwindow6.10.1 Configuration - Rack data Subwindow: Configu

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1318￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Table viewThe rack table cannot be edited directly. With a click on th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1319Rack nameName for the new rack. The selected name must not already exist.Input2

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1320￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)in by the Sample Processor in order to recognize the rack. If no rack

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1321Rack offsetThe rack offset is a production-dependent tolerance value between th

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1322￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 235 mmRinse positionRinse position for Lift 2. This lift po

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1323Work position Tower 1Work position for the special beaker at Tower 1.Work posit

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭118￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Run test errorThis display appears if an error has occurred during the run tes

6.10 Rack data subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1324￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Beaker radiusRadius of the selected special beaker on the rack. If the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6 Configurationtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1325￭ Special beakersDisplay of the special beaker for the rack in position.6.10.3.

7.1 Titrando￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1326￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7 Devices7.1 Titrando7.1.1 Titrando - OverviewThe parameters for the 808, 809,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1327Device typeDisplay of the device type.Program versionShows the program version of the

7.1 Titrando￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1328￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measuring input 1/2 (iConnect)ADC typeShows the type of analog-digital converter.S

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1329At program starton | off (Default value: on)If this option is switched on then at eac

7.1 Titrando￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1330￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.1.5 Properties - GLPTab: Configuration ▶ Device ▶ [Edit] ▶ Properties... ▶ &apo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1331Message by E-mailon | off (Default value: off)The message is additionally sent to the

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1332￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Old versionShows the old device program version.New versionShows the new device pro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1333Titrino Program version702 SM Titrino 5.702.0021716 DMS Titrino 5.716.0022718 STAT Ti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭119The button is present in the status BUSY (determination is running), CONDREADY (cond

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1334￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Update]Opens the dialog window Load new program version (see Chapter7.1.6, page 13

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1335At program starton | off (Default value: on)If this option is switched on then at eac

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1336￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Time intervalon | off (Default value: off)If this option is switched on then the re

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1337NoteThese parameters are only editable for devices with status not ok (powersupply an

7.2 Titrino￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1338￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Only editable when the monitoring is activated.Default value 　　　 GLP test date + 99

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13397.3 756/831 Coulometer7.3.1 756/831 Coulometer - OverviewDialog window: Configurati

7.3 756/831 Coulometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1340￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Start-upShows the date on which the device was automatically added to th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1341NoteThese parameters are only editable for devices with status not ok (powersupply an

7.3 756/831 Coulometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1342￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Only editable when the monitoring is activated.Default value 　　　 GLP tes

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13437.4 712 Conductometer7.4.1 712 Conductometer - OverviewDialog window: Configuration

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭120￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ERRORError.3.6.3.4 Single determination - Determination parameters Subwindow:

7.4 712 Conductometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1344￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Start-upShows the date on which the device was automatically added to the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1345NoteThese parameters are only editable for devices with status not ok (powersupply an

7.4 712 Conductometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1346￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Only editable when the monitoring is activated.Default value 　　　 GLP test

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13477.5 856 Conductivity Module7.5.1 856 Conductivity Module - DeviceDialog window: Con

7.5 856 Conductivity Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1348￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device serial numberShows the serial number of the device.Start-upS

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1349R (25 °C)Nominal resistance of connected NTC sensor.Only visible with temperature sen

7.5 856 Conductivity Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1350￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)allTime interval after which the request to prepare the dosing devi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1351Monitoring of GLP validityMonitoring of GLP validityon | off (Default value: off)If t

7.6 867 pH Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1352￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ActionThe actions can only be edited if monitoring is switched on.If during m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13537.6.2 Properties - GeneralTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Pr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭121menu item Delete statistics, whereby the already calculated statistics datais delete

7.6 867 pH Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1354￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.6.3 Properties - Measuring inputsTab: Configuration ▶ Devices ▶ [Edit] ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13557.6.4 Properties - MSB #Tab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Pro

7.6 867 pH Module￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1356￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stirrer 1Stirrer typeDisplay of the stirrer type.Stirrer serial numberDisplay

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13572.5.1, page 79). After the date has been entered, the field GLP test inter-val will b

7.7 846 Dosing Interface￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1358￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.7 846 Dosing Interface7.7.1 846 Dosing Interface - OverviewDialog

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1359Start-upShows the date on which the device was automatically added to the devicetable

7.7 846 Dosing Interface￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1360￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)allTime interval after which the request to prepare the dosing device

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1361Monitoring of GLP validityMonitoring of GLP validityon | off (Default value: off)If t

7.8 730 Sample Changer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1362￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ActionThe actions can only be edited if monitoring is switched on.If dur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1363￭ GLPInformation on GLP tests and GLP monitoring.7.8.2 Properties - GeneralTab: Conf

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭122￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample positionPosition of the sample on the rack. This number is used to move

7.8 730 Sample Changer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1364￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input1000 charactersDefault valueempty7.8.3 Properties - TowerTab: Conf

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13657.8.4 Properties - RackTab: Configuration ▶ Device ▶ [Edit] ▶ Properties... ▶ Proper

7.8 730 Sample Changer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1366￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteConnecting the dosing devices is described in the manual for the 730

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1367Comment GLP testComment on GLP test.Input1000 charactersMonitoring of GLP validityMon

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1368￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Acoustic signalon | off (Default value: off)If this option is ena

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1369￭ Dosing deviceProperties of the connector and the dosing devices connected to. Thist

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1370￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Start-upShows the date on which the device was automatically adde

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1371Rack codeShows the rack code of the rack attached. The rack code corresponds to thear

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1372￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.9.6 Properties - OvenTab: Configuration ▶ Device ▶ [Edit] ▶ Pr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13737.9.7 Properties - GasTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ Proper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭123Sample size unitSample size unit (initial weight). There are no restrictions on the

7.9 774 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1374￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Disconnect]Disconnects the connection to the RS-232 device.NoteT

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1375Only editable when the monitoring is activated.Default value 　　　 GLP test date + 999

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1376￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.10 778/789 Sample Processor7.10.1 778/789 Sample Processor -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1377[Update]Opens the dialog window Load new program version (see Chapter7.1.6, page 1331

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1378￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)tions(see Chapter 6.10.3.2, page 1320) and Special beakers(see Ch

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1379[Configuration]Opens the dialog window Configuration (see Chapter 7.11.7, page1391) i

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1380￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range3 ... 20 °/sDefault value20 °/s[Rack Data]Opens the dialog w

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1381Connected devicesInformation about the following peripheral devices connected to the

7.10 778/789 Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1382￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThese parameters are only editable for devices with status no

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1383Only editable when the monitoring is activated.Default value 　　　 GLP test date + 999

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭XII￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)9.2.3 Backing up configuration data ...

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭124￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample positionPosition of the sample on the rack. This number is used to move

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1384￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.11 814/815 USB Sample Processor7.11.1 814/815 USB Sample

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1385This button is only displayed with devices that have their own firmware. Itis only ac

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1386￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)this minimum beaker radius is undercut then the run will be s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1387[Configuration]Opens the dialog window Configuration (see Chapter 7.11.7, page1391) i

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1388￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range3 ... 20 °/sDefault value20 °/s[Rack Data]Opens the dial

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1389Connected devicesInformation about the following peripheral devices connected to the

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1390￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)GLP test intervalTime interval to next GLP test. If a value i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1391Display messageA message is displayed and you can choose whether you want to con-tinu

7.11 814/815 USB Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1392￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range-270.0 ... 270.0 °Default value0.0 °Swing directionThe s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13937.12 855 Robotic Titrosampler7.12.1 855 Robotic Titrosampler - OverviewDialog windo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭125Sample size unitSample size unit (initial weight). There are no restrictions on the

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1394￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)This button is only displayed with devices that have their own fi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1395With the 856 Conductivity Module displayed only.SelectionPt 1000 | NTCDefault valuePt

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1396￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Lift rateLift speed for manual operation.Range3 ... 25 mm/sDefaul

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1397Table for external positionsThe properties for the 4 possible external positions for

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1398￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Rack Data]Opens the dialog window Rack data (see Chapter 6.10.3.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1399Connected devicesInformation about the following peripheral devices connected to the

7.12 855 Robotic Titrosampler￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1400￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)GLP test intervalTime interval to next GLP test. If a value is en

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1401Display messageA message is displayed and you can choose whether you want to con-tinu

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1402￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Program versionShows the program version of the device.Only v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1403Min. beaker radiusDefinition of the minimum radius which the beakers used on the rack

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭126￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Check device (modules) and rackCheck whether the instruments (and/or instrum

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1404￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Rinse positionRinse position valid for all 4 external positio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1405Number of positionsShows the number of positions on the rack. If no rack is in positi

7.13 864 Balance Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1406￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Time intervalon | off (Default value: off)If this option is s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1407Input1000 charactersMonitoring of GLP validityMonitoring of GLP validityon | off (Def

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1408￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ActionThe actions can only be edited if monitoring is switched o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭14097.14.2 Properties - GeneralTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties... ▶ P

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1410￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.14.3 Properties - TowerTab: Configuration ▶ Devices ▶ [Edit]

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1411[Rack Data]Opens the dialog window Rack data (see Chapter 6.10.3.1, page 1319) orRack

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1412￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Connected devicesInformation about the following peripheral devi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1413With the 774 Oven Sample Processor display of the initial temperature seton the devic

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭127￭ Check sample dataCheck whether the sample data entered corresponds to the definedm

7.14 874 Oven Sample Processor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1414￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Monitoring can only be switched on when a date has been entered

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1415Record messageThe message that the validity period has expired will be automaticallys

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1416￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input50 charactersDefault valueDevice type number_#Device typeDisplay

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1417Selectioncontinuous | pulsedDefault valuecontinuousPulses per integration timeFrequen

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1418￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.15.5 Properties - CalibrationTab: Configuration ▶ Devices ▶ [Edit]

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1419DateDisplay of date and time the dark spectrum has been recorded.UserDisplay of the u

7.15 Avantes Spectrometer￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1420￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)UserDisplay of the user logged in during recording of the reference s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1421Monitoring of GLP validityMonitoring of GLP validityon | off (Default value: off)If t

7.16 RS-232 device￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1422￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ActionThe actions can only be edited if monitoring is switched on.If during

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1423Input50 charactersDefault valueDevice type number_#Device typeDisplay of the device t

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭128￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7 - Conditioning (only for methods with conditioning)Conditioning is started w

7.16 RS-232 device￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1424￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionCOM1 | COM2 | … | COMnDefault valueCOMnCOMnFirst free COM port.Baud

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1425Selection\0D | \0D\0A | \0D\0A\0A | \0D\0D\0ADefault value\0D\0A(\0D = CR, \0A = LF)T

7.16 RS-232 device￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1426￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input1000 charactersMonitoring of GLP validityMonitoring of GLP validityon |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1427ActionThe actions can only be edited if monitoring is switched on.If during monitorin

7.17 Balances￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1428￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.17 Balances7.17.1 Balance - OverviewDialog window: Configuration ▶ Devices ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1429Start-upShows the date on which the device was automatically added to the devicetable

7.17 Balances￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1430￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionNone | Odd | EvenDefault valueNoneStop bitNumber of stop bits.Selection1

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1431GLP test intervalTime interval to next GLP test. If a value is entered here then the

7.17 Balances￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1432￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Display messageA message is displayed and you can choose whether you want to con-

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭14337.18 Barcode reader7.18.1 Barcode reader - GeneralA barcode reader is used to enter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1293.6.3.9.2 Properties - Display Dialog window: Workplace ▶ Run ▶ Single determinat

7.18 Barcode reader￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1434￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.18.2 Barcode reader - OverviewDialog window: Configuration ▶ Devices ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1435Data storage under legal controlIndicates whether the balance has its own calibratabl

7.18 Barcode reader￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1436￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input1000 charactersMonitoring of GLP validityMonitoring of GLP validityon

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1437ActionThe actions can only be edited if monitoring is switched on.If during monitorin

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1438￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.19 IO controller7.19.1 IO controller - OverviewDialog window: Configurat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1439Device serial numberDisplay of the serial number of the device.Set to workShows the d

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1440￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.19.4 Properties - Digital inputsTab: Configuration ▶ Devices ▶ [Edit] ▶ P

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1441Input50 charactersDefault valueDigIn_x_y_zThe following characters must not be part o

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1442￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Assigned outputSelection of an output port assigned to an input port. The si

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1443ActionOnly active and editable for the Port type = Level detector.If the fill level i

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭130￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2 columnsIf this option is selected, then the sample identifications ID1…ID16

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1444￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Parameter 2The meaning of Parameter 2 depends on the Type set.[Edit]Opens th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1445NoteAdditionally a stepping motor can have a port of the Type = Brake.The port inform

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1446￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ >0: For 100% stirrer output (Parameter 1 = 100), pulse duration in 10ms

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1447The menu [Port description] contains the following menu items:ImportImport of a text

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1448￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteWith the aid of the following parameters the physical values that areadj

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1449High level (100%)Display of the highest analog output value with unit.0% MappingMeasu

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1450￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input50 charactersDefault valueAnOut_x_y_zThe following characters must not

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1451Default valueDisplay of the default value the outputs takes directly after starting a

7.19 IO controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1452￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Next GLP testDate on which the next GLP test is to be carried out. The date

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1453Stop determinationThe running determination will be automatically terminated. The fol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭131Request assignment IDon | off (Default value: off)If this option is enabled, the Ass

7.20 Stepping motor controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1454￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)AdsDll versionDisplay of the version of AdsDll.dll.Device serial

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭14557.20.4 Properties - Digital inputsTab: Configuration ▶ Devices ▶ [Edit] ▶ Properties

7.20 Stepping motor controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1456￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input50 charactersDefault valueDigIn_x_y_zThe following characte

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1457Assigned outputSelection of an output port assigned to an input port. The signal of t

7.20 Stepping motor controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1458￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ActionOnly active and editable for the Port type = Level detecto

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1459Parameter 2The meaning of Parameter 2 depends on the Type set.[Edit]Opens the dialog

7.20 Stepping motor controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1460￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteAdditionally a stepping motor can have a port of the Type =

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1461￭ >0: For 100% stirrer output (Parameter 1 = 100), pulse duration in 10msExample:P

7.20 Stepping motor controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1462￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.20.6.1 Properties Stepping motorDialog window Configuration ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1463ResetA reset is carried out on the terminal the motor is connected to. Whiledoing so,

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭132￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionAlways accept data | Accept data only foractive windowDefault valueAl

7.20 Stepping motor controller￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1464￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)7.20.7 Properties - GLPTab: Configuration ▶ Device ▶ [Edit] ▶ P

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 Devicestiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1465Message by E-mailon | off (Default value: off)The message is additionally sent to the

8.1 Manual Control - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1466￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)8 Manual Control8.1 Manual Control - GeneralProgram part: Manual

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭14678.3 Manual Control - Device selectionProgram part: Manual ControlIn the subwi

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1468￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrino: 702, 716, 718, 719, 720, 721, 736, 751, 758, 785, 784,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1469TiterDisplay of the titer of the solution put on. This field only appears for

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1470￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)8.4.1.5 Dosing - EmptyProgram part: Manual ControlHere the empt

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1471730, 774, 778, 789Range0.01 ... 160.00 mL/minTitrinoRange0.01 ... 150.00 mL/mi

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1472￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteParameters modified after the start of the dosing are not va

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1473NoteFor viscous liquids the filling rate should be reduced.SelectionmaximumDef

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭133Confirmation necessary to accept data during the determination.on | off (Default val

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1474￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrino: 751, 758, 785, 784, 785, 794, 795, 798, 799Titrando: 80

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1475[Start]Start continuous operation for the selected stirrer. In the status disp

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1476￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Output signalCurrent statusDisplays the current status of the 14

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1477NoteWe recommend masking the irrelevant output lines with an asterisk * soas n

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1478￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Rack codeShows the number of positions on the rack attached. If

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1479Current positionShows the current rack position.Target positionSelect or enter

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1480￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Start]Start moving to target position. Start moving to target p

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1481Current positionShows the current rack position.Special beakerSelect the speci

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1482￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Shift position forIf this option is selected, the current lift p

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1483External positionSelect the external position to which the current robotic arm

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭XIII9.8 Sample tables ...

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭134￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Sample dataEntry of sample data for the next determinations.￭ PropertiesDefi

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1484￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionOn/Off | DurationDefault valueOn/OffDurationEnter the d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1485Gas flowInletSelect the inlet of the carrier gas.SelectionPump | ValveDefault

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1486￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Inert gas valveSwitch the inert gas valve on the Oven Sample Pro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1487Measured quantityThe selectable measured quantities depend on the device whose

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1488￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange-127 ... 127 µA (Increment: 1)Default value5 µAU(pol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1489Sample solutionSelect name from the table Sample solution (TC conductivity).Se

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1490￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Measuring]Start measuring of the intensity. The parameters defi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭14918.4.6.2.1 Digital inputs - OverviewProgram part: Manual ControlIf in the devi

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1492￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)PortDisplay of the internal description of the port.TypeDisplay

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1493Graphical displayExample:Dig-Out_1_4_1Type: PumpStatus: ACTIVEDig-Out_1_4_2Typ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭135Interrupt seriesWith this button, the ongoing determination of a sample series will

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1494￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)8.4.6.3.2 Digital outputProgram part: Manual ControlIf in the d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1495StatusDisplay of the current status.SelectionACTIVE | INACTIVE | ERROR[Start]S

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1496￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Start delayWaiting time in seconds or minutes before the initiat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1497TypeDisplay of the port type.StatusDisplay of the current status.SelectionACTI

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1498￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)8.4.6.4 Analog inputsProgram part: Manual Control8.4.6.4.1 Ana

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1499Graphical display8.4.6.5 Analog outputsProgram part: Manual Control8.4.6.5.1

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1500￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)8.4.6.5.2 Analog outputProgram part: Manual ControlIf in the de

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1501[Set]Sets the analog output to the mapping value indicated.Set defaultPort des

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1502￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Switch on/off[Start]Sets all stepping motors to ACTIVE.[Stop]Set

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1503TypeDisplay of the port type.DistanceDistance to be moved to.Visible only in c

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭136￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ERRORError.3.6.4.4 Determination series - Determination parameters Tab: Workp

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1504￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)PortDisplay of the internal description of the port.TypeDisplay

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1505TimeoutTime in seconds or minutes within which the action must have run throug

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1506￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionACTIVE | INACTIVE | ERROR[Start]Sets the stepping motor

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1507Reference posi-tionBrakeSafety switch 1 Safety switch 2 Safety switch 3 Overvi

8.4 Manual Control - Functions￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1508￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range1 ... 12 Default value1 Shift directionSelect the direction

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8 Manual Controltiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15098.5 Manual Control - Graphical displayProgram window:Manual controlIn the sub

9.1 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1510￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)9 How to proceed?9.1 Audit Trail9.1.1 Opening Audit Trail How to proceed?Not

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1511After this function has been selected, the field in which the cursor islocate

9.1 Audit Trail￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1512￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The dialog window Audit Trail opens. 3If desired, filter Audit Trail table. 4If

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1513 4Enter or select directory and file name for saving the archive file in thef

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭137The second field after Autostart shows the total number of determinationsper series

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1514￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 3Archive desired Audit Trail entries. 4With the menu item File ▶ Delete the dialog

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1515Backing up database manually 1Select program part Database. 2Click on the sym

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1516￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 4On the tab General enter a comment on the database in the fieldComment. 5On the ta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1517NoteExisting databases cannot be overwritten, i.e. they must first bedeleted

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1518￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIf the backup directory is on a network drive. the backup date shouldbe added ma

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1519The dialog window Restore configuration data opens. 3Select the directory in

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1520￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 2Click on the menu item File ▶ Backup ▶ Manually.The dialog window Backup configura

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1521Exporting methods 1Select program part Method. 2Click on the symbol or menu

9.2 Backup￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1522￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 3Click on the menu item File ▶ Archive...The dialog window Archive Audit Trail ope

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15239.3 Determinations9.3.1 Starting single determinationHow to proceed?Single

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭138￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.6.4.5 Determination series - Sample data Tab: Workplace ▶ Run ▶ Determina

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1524￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIn order to calculate statistical calculations for results, the Statis-t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1525 5If a method was loaded in which the option Statistics in the STARTcommand i

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1526￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIf the method contains a DATABASE command, then it is manda-tory that th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1527The dialog window Open database opens. 3Select desired database or enter name

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1528￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 4Click on [Save filter]. 5Click on [Apply filter].The table will be filtere

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1529Signature 1NoteDeterminations can only be signed at level 1 if the user belon

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1530￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The window Signature Level 2 opens; if a signature is possible forthe select

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1531 2Click on the symbol or the menu item File ▶ Open...The dialog window Ope

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1532￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 5Click on the menu item Determinations ▶ Import...The window Import determ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1533NoteIf the option Comment on modification of determinations inthe Security se

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭139Reset sample tableResets lines that have been run, i.e. they can be edited again.Dup

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1534￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)9.3.10 Reprocessing determinations How to proceed?NoteDeterminations that h

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1535The selected determinations are recalculated. The results of this recal-culat

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1536￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The selected determinations are recalculated. The results of this recal-cula

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1537If the determination is switched off then an asterisk (*) appears behindall r

9.3 Determinations￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1538￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 4Modify curve evaluation manually. 5Then close the window with [OK]. 6Click

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1539 6Click on the menu item File ▶ Print ▶ Report...The dialog window Report ou

9.4 Databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1540￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteA maximum of 4 databases can be opened, but only 2 can be dis-played at the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1541NoteEach determination database has to be backed up separately. Afterwards,it

9.4 Databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1542￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Closing all databases 1Select program part Database. 2Click on menu item File ▶ C

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1543 9On tab Monitoring, define monitoring of size and number of datasets.9.4.5

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭140￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Unmark linesRemoves the line marking for the selected lines.Set lines inexecut

9.4 Databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1544￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 3Select desired database. 4Click on [Properties].The dialog window Properties -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1545 6Enter the name under Save as under which the database is to berestored. 7Cl

9.5 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1546￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)9.5 Configuration data9.5.1 Configuration data in generalThe configura

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15479.5.3 Importing configuration dataHow to proceed?1Select program part Config

9.5 Configuration data￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1548￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 4Select or enter the name for the Backup file. If an existing backup fi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1549 2Start the file ConfigRestore.exe in the program directory …\tiamo\bin.The d

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1550￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)9.6 Methods9.6.1 Open methodHow to proceed?1Select program part Method. 2Click on

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1551Close all methods 1Select program part Method. 2Click on menu item File ▶ Clo

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1552￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 2In the list box Method group select the desired method group. 3Select the desired

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15539.6.6 Exporting method How to proceed?1Select program part Method. 2Click on

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭141RemarksFreely definable remarks concerning the determination, that are savedtogether

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1554￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The dialog window Select files to import opens. 5Select desired import files named

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1555The selected method will be signed on level 1.NoteMethods can be signed more

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1556￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The dialog window Method manager opens. 3In the list box Method group select the de

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15579.6.11 Backup methodsHow to proceed?GeneralMethods are stored in the configu

9.6 Methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1558￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 3Activate the Automatic backup check box. 4Enter an interval for backup monitoring

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15599.7 Method groups9.7.1 Creating method groupHow to proceed?1Select program

9.8 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1560￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 4Click on [Delete].The selected method group is deleted. 5Confirm deleting w

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1561 9Repeat step 6 for each desired determination. 10Click on [Close].The dialog

9.8 Sample tables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1562￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 9Click on the menu item Edit ▶ Edit line in the dialog window Sampletable.Th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15639.8.4 Edit working sample tableHow to proceed?1Select program part Workplace

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭142￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Authorization for carrying out the method?Check whether the registered user

9.9 Reports￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1564￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 14In the field Name enter a name. 15Click on [Save].The working sample table will

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1565 9Select desired module symbol on the Module bar and place it on thereport te

9.9 Reports￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1566￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab) 7Close the dialog window with [OK]. 8In the program window Report template, click

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15679.9.3 Printing determination report How to proceed?1Select program part Data

9.9 Reports￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1568￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIf several reports are produced simultaneously as a PDF file then anindex will

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭9 How to proceed?tiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1569 8Under Orientation, select the option Portrait format or Landscapeformat. 9C

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1570￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)IndexNummern/Symbole21 CFR 11 ... 14, 1201, 1202, 1207, 1208712 ConductometerOvervi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1571Beaker radius ... 1325, 1377, 1385, 1395, 1402Rack parameters ... 1320Rack ta

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1572￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DIGITAL OUT ... 1163DOS pH ... 1047DOS U ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1573Statistics ... 238Control chart templatesExport ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭143￭ Conditioning condition fulfilledIf the conditioning requirement has been fulfilled

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1574￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Version ... 322, 327, 1533Determination overviewColumn display ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1575Overview ... 1168Digital inputManual Control ... 1490DIGI

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1576￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Parameters for preparing ... 1266Prepare ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1577Greater than or equal to ... 55Group fieldGroup field ... 227

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1578￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Graphical display ... 1509Heater/Gas ... 1484Measure ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1579Messages ... 168, 1160MET ... 536Ev

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1580￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Line ... 229Module bar ... 206Number of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1581Overview ... 11Workplace ... 12, 82Program vers

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1582￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Result ... 1116Assignment ... 1116Decima

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1583Limits ... 1289Monitoring ... 1282, 1289Parameter ...

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭144￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Interrupt and continue seriesA series that is running can be interrupted at

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1584￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)979, 987, 1037, 1050, 1065, 1078Solution table ... 1255Subwindow ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Indextiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1585Stop measured value 444, 471, 497, 524, 551, 576, 603, 628, 865, 878, 890, 903, 916, 92

Index￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1586￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SERIES START ... 424START ... 413TRACK ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭145￭ Conditioning condition fulfilledIf the conditioning requirement has been fulfilled

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭146￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Loading sample tableNameName of the sample table that is to be loaded. If a sa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭147for the quick selection of methods in the Method field. This button is activeonly if

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭148￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIf a value is entered or imported into this field, then in addition the ti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭149Jump to the previous line in the working sample table.Option of entering the desired

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭150￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range1 ... 999 Default value1 3.6.4.9.5 Importing sample dataDialog window: W

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭151File typePrescribed format *.csv.Selection[*.csv]Default value[*.csv][Save]The sampl

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭152￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample table test finished with errorsThis display appears if an error has occ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭153[Save]Save the sample table under the desired name.3.6.4.9.9 Run testMenu item: Wor

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭11 Introduction1.1 Welcome to tiamoIntroductiontiamo = titration and moretiamo is

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭154￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Run test running…This display appears during the test run. A progress bar also

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭155￭ ProcessOptions for processing the working sample table on the tab Determi-nation s

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭156￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample numberon | off (Default value: on)Enable/disable the display of the fie

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭157Input50 charactersDefault valueID1…3ID4 … ID16on | off (Default value: off)Enable/di

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭158￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)into the same line. This means that it is possible, for example, to fill a lin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭159Sample size uniton | off (Default value: on)If this option is enabled, then the cont

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭160￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Actions for marked sample table linesSelectionPause series ([Pause]) and show

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭161BalanceSelection of the balance from which data is to be imported.SelectionDevice na

3.6 Subwindow Run￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭162￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Accept data only for active windowIf this option is selected, then the data se

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭163*.csv (Unicode)Format for the import of CSV files with Unicode character sets.3.6.4.

1.2 Operation￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Database-based program with Client/Server functionality￭ A wide range of import an

3.7 Subwindow Method￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭164￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.7 Subwindow Method3.7.1 Method window - GeneralSubwindow: Workplace ▶ M

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭165SelectionFit in windowDefault valueFit in windowAdjust to both height and width of t

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭166￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.7.4 Method window - Cancel commandSubwindow: Workplace ▶ MethodIf

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭167On these tabs the live display elements (curve, measured value, message)defined in t

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭168￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.8.3 Live display - Application noteSubwindow: Workplace ▶ Live dis

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭169Measured value 1…3Select the measured values for the measured value display. The mea

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭170￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)MEAS TC CondSelectionoff | Measured value | time | dMW/dt | Calcula-t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭171KFC / BRCSelectiontime | Measured value | amount | drift | Charge| dV/dt | Ugen | Ig

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭172￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)METSelectionMeasured value | Volume | time | Temperature| dMW | Calcu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭173DOSSelectionVolume | Measured value | Temperature | time| dV/dt | Calculated 1…3 | E

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭31.3 Connecting devicesIntroductiontiamo brings together the world of Titrino devic

3.8 Subwindow Live display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭174￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)MEASSelectionoff | Measured value | time | Temperature |dMW/dt | Calc

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭175Display gridon | off (Default value: off)If this option is enabled, a grid will be d

3.9 Subwindow Report￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭176￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3.9.4 Report overviewTab: Workplace ▶ Report ▶ Report overviewThe reports

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1774 Database4.1 Database - General4.1.1 Database - DefinitionProgram part: DatabaseD

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭178￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ElementsThe desktop of the program part Database comprises the following

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭179Report…PDF file output of the report (see Chapter 4.5.2.12, page 320).Logout...Logout

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭180￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.1.3.5 Database - Menu DeterminationsProgram part: DatabaseComment...En

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭181Make current Make the old version selected in the history view the current version ag

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭182￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.1.3.7 Help MenuProgram part: Workplace / Database / Method / Configura

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭183Filter/Quick filter Use quick filter with the content of the selected table cell (see

1.4 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)1.4 Method editorIntroductionThe new graphic method editor gets more out of you

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭184￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.1.5 Database - SubwindowsProgram part: DatabaseSelectionThe following

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭185Determinations￭ Overview of functionsTemplates￭ Edit report templates￭ Edit control c

4.1 Database - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭186￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)As an alternative a standard view can be defined for each user group that

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭187Move the selected subwindow downward (modifies sequence).4.1.7.3 Load viewDialog win

4.2 Database display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭188￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.1.7.5 Rename viewDialog window:Workplace / Database / Configura-tion ▶ V

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭189EditableShows whether or not the database can be edited by the user currentlylogged i

4.2 Database display￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭190￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Two databases are opened. Normally only one databaseis displayed in the mai

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1914.3 Manage databases4.3.1 Manage databasesDialog window: Database ▶ File ▶ Database

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭192￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the window Database manager for editing the database sele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭193NoteThe database name must be unambiguous in the whole Client/Server sys-tem.4.3.4 D

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭5in this network and can be accessed and processed by all Client PCs. Allclients als

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭194￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SizeShows the size of the database in KB.CreatedShows the date and time of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1954.3.5.4 Database properties - BackupDialog window: Database ▶ File ▶ Database manage

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭196￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteMake sure that you have read and write access rights on the selecteddir

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭197Backup targetBackup directorySelection of a folder predefined in Program administrati

4.3 Manage databases￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭198￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Backup nameSelection of a backup file.SelectionSelect backup filesBackup da

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭1994.4 Templates4.4.1 Report templates4.4.1.1 Manage report templates4.4.1.1.1 Repor

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭200￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.4.1.1.2 Rename report templatesDialog window: Database ▶ Tools ▶ Report templat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2014.4.1.1.6 Import report templatesDialog window: Database ▶ Tools ▶ Report templates

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭202￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SavedDate and time when the report template was saved.Saved byShort name of the us

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2034.4.1.4.1.2 Report template - DesktopProgram window: Database ▶ Report templateEleme

1.7 Conformity￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Various export formats , e.g. XML, CSV, SLK (see Chapter 4.4.4.2.1, page245).￭ Au

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭204￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Print (PDF)... Show the report template with the data of the selected determinatio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2054.4.1.4.1.3.6 Report template - Menu ToolsProgram window: Database ▶ Report template

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭206￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.4.1.4.1.5 Report template - Module-specific toolbar Program window: Database ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭207Line If this option is switched on then lines can be inserted in the report template

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭208￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Apply to all pagesThe page settings are applied for all report pages.Page formatPa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭209Range0.0 ... 499.0 mmDefault value20.0 mmRightRight-hand page margin.Range0.0 ... 499

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭210￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Defining sections for tabular reportThe header, footer and report sections can be

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭211Jumps to last page.4.4.1.4.2.5 Report template - Insert modules Program window: Data

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭212￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Select a single moduleSingle modules are selected with a click of the left mouse b

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2134.4.1.4.2.8 Report template - Page preview Preview window: Report template ▶ File ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7￭ Digital signature on two levels (see Chapter 2.3, page 17).￭ One signature each f

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭214￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Jumps to last determination. 4.4.1.4.2.9 Report template - CommentDialog window:

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭215Snap at gridon | off (Default value: off)Enable/Disable snapping at grid on the repor

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭216￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input50 charactersNoteThe name of the report template must be unambigous in the wh

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭217Selection of the available Windows fonts.Font size in pt.Color selection.Bold.Italic.

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭218￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)InsertIn order to insert a data field into a report template the corresponding sym

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭219Left-justified.Centered.Right-justified.Switches line break on/off for multi-line dat

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭220￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)InsertIn order to insert a date field into a report template the corresponding sym

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭221Left-justified.Centered.Right-justified.Fills the field with dots.PrefixText placed i

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭222￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0.0000 ... (max. page height) mmWidthWidth of time field.Range0.0000 ... (max

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭223SuffixText to be placed after the contents of the time field.Input50 charactersPrevie

1.9 Online help￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)1.9 Online helpIntroductionCalling up the Helptiamo has an extensive and detailed

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭224￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Color selection.Bold.Italic.Underlined.Left-justified.Centered.Right-justified.Fil

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭225InsertIn order to insert a number of pages field into a report template, the corre-sp

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭226￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Left-justified.Centered.Right-justified.Fills the field with dots.PrefixText place

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭227WidthShows the predefined width of the fixed report.HeightHeight of fixed report.Rang

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭228￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe following fields, which do not permit page break controls, cannot beinsert

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭229PropertiesX pos.x-position within the permitted section.Range0.0000 ... (max. page wi

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭230￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)InsertIn order to insert a line in a report template the corresponding symbol must

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2314.4.1.4.3.11 Report template - Rectangle Program window: Database ▶ Report templateA

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭232￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selection of the fill color.4.4.1.4.3.12 Report template - Curve field Program wi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭233SelectionDET | MET | SET | MEAS | MEAS T/Flow | MEASTC Cond | MEAS Ref | MEAS Opt | M

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 Introductiontiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9WarningThis symbol draws attention to a possible hazard dueto heat or hot instrumen

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭234￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)InsertIn order to insert calibration curve field into a report template the corre-

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭235Template tableThe table with the defined templates cannot be edited, although it can

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭236￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Graphical parametersParameters for the graphical display of the control chart.￭

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭237ColorSelection of the color for the measuring point symbol.SelectionColor selection |

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭238￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.4.2.2.4 Control chart template - StatisticsDialog window: Database ▶ Tools ▶ Te

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭239Template tableThe table with the defined templates cannot be edited, although it can

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭240￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionDET pH | DET U | DET Upol | DET Upol | METpH | MET U | MET Ipol | MET Upo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭241ScalingStart valueInitial value for scaling the x axis.Range-1.0 E12 ... 1.0 E12 Defa

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭242￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ScalingStart valueInitial value for scaling the y-axis.Range-1.0 E12 ... 1.0 E12 D

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭243Manual EPsSelects the color for manually set endpoints.SelectionColor selection | pin

1.10 What is new in tiamo 2.1?￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭10￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Titrino: The window evaluation does not work correctly.￭ 778, 78

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭244￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.4.4 Export templates4.4.4.1 Managing export templatesDialog window: Database ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2454.4.4.2 Editing export templates4.4.4.2.1 Export template - Properties Dialog win

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭246￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)*.csv (measuring point list)Data exchange format for the measuring point list with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭247Sample identificationIf this option is selected then the name of the export file will

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭248￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Remove selected field.Modifies the sequence of the exported fields by moving the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭249Field separatorSelection of the field separator.Selection; | , | TabDefault value;4.4

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭250￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<userNameFull val="" />User name (full name)<clientName val=&qu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭251<determinationEndState val=""/>Determination run (way in which the de

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭252￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<status val="original"/>Determination status:originalDetermination

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭253<vt val=""/>Variable type:TX = TextNR = NumberDT = Date/TimeNA = Unkn

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭112 General program functions2.1 Program parts2.1.1 Program partsGen

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭254￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)– <comment>...</comment>Comment on the signature.</data> </si

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭255<savingTime val=""/>Date and time when the modified method version wa

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭256￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<vs val=""/>Variable status:OK = The value is ok and has not been

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭257</SmplData> – <Identification>Sample identifications.– <ID__01>Samp

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭258￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<pr val=""/>Name of the CALC command the result has been gener-ate

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭259<vs val=""/>Variable status (see above).</data> <rel> <

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭260￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)– <sme>Mean value of the result.– <data> <vr val="" />

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2614.4.4.3.6 XML export - Command dataXML export– <CommandData dynamic=""&

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭262￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)– <swingHeadOneType> ... </swingHeadOneType>Type of Swing Head on towe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭263– <conc> ... </conc>Concentration.– <concUnit> ... </concUnit>

2.1 Program parts￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭12￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Manual program part￭ Manual control of devicesNoteAccess to the individual prog

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭264￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<adcSerial val="" />Serial number of measuring input.<tempSenso

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭265<sensorC val="" />Blank value of the ISE sensor.<resultUnit val=&q

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭266￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<variance val="" />Variance.– <StdAddTable>Standard addition

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭267</tableBody> </MeasPoints> – <EndPoints dynamic="">Endpoi

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭268￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)<volume> ... </volume>Volume in mL.<otherVal> ... </otherVal&

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭269<am val="" />Assignment method.<at val="" />Assignmen

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭270￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)– <dateRecDarkRefSpec> ... </dateRecDarkRefSpec>Recording time of dark

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭271– <Solution>Data on solution.– <solTitle> ... </solTitle>Solution t

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭272￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)– <usedSensors dynamic="">Sensor data– <Sensor>Data on senso

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭273<sensorCalMethod val="" />Calibration method.<sensorCalMeasInput v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭13shown in color. The upper left corner of the symbol contains a black

4.4 Templates￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭274￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)</TcSampleSolution> </TcSampleSolutions> 4.4.4.3.11 XML export - Meth

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭275– <sme> ... </sme>Mean value of the result.– <un> ... </un>Re

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭276￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5 Determination overview4.5.1 Determination overview - General4.5

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭277Table viewWith a click on the column title the table can be sorted according to these

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭278￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Removes the selected column from the table.Move selected column upwar

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2794.5.1.5 Determination overview - Navigation barSubwindow: Database ▶ Determination o

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭280￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Page Up]Pages backward within the current set.[Page Down]Pages forwa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭281￭ Several determinations not in sequenceIn order to select several determinations not

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭282￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2 Determination overview - Functions4.5.2.1 Update determinatio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭283[More...]Open the dialog window Search – Field selection. All fields are listed intre

Metrohm AGCH-9101 HerisauSwitzerlandPhone +41 71 353 85 85Fax +41 71 353 89 [email protected] 2.1 (ProcessLab)Online Help8.101.80

2.2 Login/password protection￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭14￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ElementsThe desktop of the program part Configuration comprises the

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭284￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)outside limitsIt is being searched for values which exceed the limit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭285SelectionTotal | Downward | UpwardDefault valueTotalTotalIt is being searched down to

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭286￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.4.3 Determinations - Quick filter Menu item: Database ▶ Determ

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭287Table viewThe overview table shows all the defined filter criteria and cannot be dire

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭288￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.4.7 Determinations - Save filterDialog window: Database ▶ Dete

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭289Selection'Field name'Filtering is carried out only for the selected field.

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭290￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)out of limitsValues that are out of the defined limits for the select

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭2914.5.2.5 Signing determinations4.5.2.5.1 Rules for electronic signaturesProgram part

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭292￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Methods or determinations can be signed at Level 1 in the Signature L

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭293[Sign]Sign method or determination. The window remains open.NoteMethods or determinat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭15￭ A login with user name and password is required each time theprogra

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭294￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Input24 charactersPasswordPassword entry.Input24 charactersReasonSele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭295ReasonReason for signature.Signature commentComment on the signature.4.5.2.5.5 Delet

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭296￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.6 Determinations - Reprocessing4.5.2.6.1 Reprocessing - Gener

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭297FunctionsIf determinations have been edited in the subwindow Modifications thenthe fo

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭298￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.6.3 Reprocessing rulesDialog window: ReprocessingThe following

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭299￭ Titration and measuring commandsFor DET, MET, SET, KFT, KFC, MEAS, CAL MEAS only th

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭300￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.6.4 Modifications4.5.2.6.4.1 Modifications - OverviewSubwindo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭301[Modify]Open the dialog window Modify variable to modify the value of an existingvari

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭302￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)(see Chapter 5.2.5, page 385). The modified method then appears on th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭303[Result on/off]Switch the selected single result for the statistical calculations off

2.2 Login/password protection￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭16￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Change password]Opens the window Change password, in which the new

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭304￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Command nameSelection of the measuring command (command name.index -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭305Set EP with parallel tangentsBy moving the mouse a point on the curve is selected to

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭306￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Define properties for the graph displayThe dialog window Properties -

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭307Measured valueMeasured value (pH) for endpoint.ERCERC value for the endpoint.TimeTime

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭308￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.6.4.6.4.2 Properties curve evaluation - x axisTab: Database ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭309Only editable when the option Autoscaling is disabled.Range-1.0E12 ... 1.0E12 Default

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭310￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)End valueEnd value for scaling the y-axis.Only editable when the opti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭311Range0.01 ... 1000 Default value0.01 Smoothing factor y-axisFactor for smoothing on t

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭312￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)CurveCurve colorSelection of the color for the curve line.Selection13

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3134.5.2.6.4.6.4.5 Properties curve evaluation - OptionsTab: Database ▶ Determinations

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭17NoteThe password always has to be changed before the Validity of the

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭314￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Show endpointsShow endpointson | off (Default value: on)If this optio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3154.5.2.6.5.1 Result view - Results overviewTab: Database ▶ Determinations ▶ Reprocess

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭316￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.6.5.2 Result view - Raw dataTab: Database ▶ Determinations ▶ R

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3174.5.2.7 Sending determinations toDialog window: Database ▶ Determinations ▶ Send to.

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭318￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)All filtered data recordsAll those determinations from the whole dete

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭319NoteIf the check box Comment on modification of determinations in theSecurity setting

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭320￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.12 Determinations - Print reportDialog window: Database ▶ File

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭321PDF fileon | off (Default value: off)If this check box is activated the reports are p

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭322￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.5.2.14 Determinations - Displaying historyMenu item: Database ▶ De

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭323values. Listed below are the individual measured values and the results forSlope, E(0

2.3 Electronic signatures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭18￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Different usersThe same user may only sign on either Level 1 or Level

4.5 Determination overview￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭324￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)If the cursor is moved to a point then the number, date and value app

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭325right of the curve the legend is shown with the line number in the determi-nation tab

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭326￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)PortraitProduces control chart in portrait format.LandscapeProduces co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3274.6.2 Information - Determination Tab: Database ▶ Information ▶ DeterminationDisp

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭328￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)StopThe determination was stopped manually with [Stop], by a stop crit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭329Determination status:Selectionoriginal | modifiedoriginalDetermination data unaltered

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭330￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Signed by (full name):Full name of user who signed the determination.S

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭331Method version:Version of the method the determination was created with.Method saving

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭332￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample size:Value for the sample size.Sample size unit:Unit of sample

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭333Modification reason sample data:Reason for the sample data modification.Modification

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭19ModifyModifyNot sigendSign (1)Signed 1Sign (2)Sigend 2Delete signatur

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭334￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measuring input:Number of the measuring input (+ designation iConnect

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭335Date titer det.:Date of the titer determination.Titer method:Method with which the ti

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭336￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Detector type:Type of the detector built in the spectrometer.Date dark

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭337Sensor serial number:Serial number of sensor.Device:Name of device to which sensor is

4.6 Subwindow Information￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭338￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Value:Value and unit of the common variables after the last value assi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭339Measuring input:Shows the type of measuring input and serial number (e.g. 1.845.00101

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭340￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.7 Subwindow Results4.7.1 Results - GeneralSubwindow: Database ▶ Result

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭341NoteOnly the last results having been calculated will be shown. For example,if there

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭342￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.7.3 Results - Raw dataTab: Database ▶ Results ▶ ResultsOn the tab Raw d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭343Table 3 Command DET IpolColumn 2: Variable Column 3 Column 4 Column 5 Column 6EP#EP#.

2.3 Electronic signatures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭20￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Signature possibleThe selected method or determination can be signed.Si

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭344￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Column 2: Variable Column 3 Column 4 Column 5 Column 6MAMA.VOL, mL, 4 MA.M

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭345Table 10 Command SET UColumn 2: Variable Column 3 Column 4 Column 5 Column 6EP#EP#.VO

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭346￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Table 14 Command KFT UpolColumn 2: Variable Column 3 Column 4 Column 5 Col

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭347Column 2: Variable Column 3 Column 4 Column 5 Column 6RE#RE#.DRT, mL/min,4RE#.DRS,mL/

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭348￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Column 2: Variable Column 3 Column 4 Column 5 Column 6ETEETE, °C, 1 FP

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭349Column 2: Variable Column 3 Column 4 Column 5 Column 6MAMA.MEA, mS/cm,2MA.TIM, s, 1 M

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭350￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Table 33 Command CAL CondColumn 2: Variable Column 3 Column 4 Column 5 Col

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭351For every single result a maximum of the following information is displayed:Result &q

4.7 Subwindow Results￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭352￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Assignment:Assigns the result to one of the result columns RS01...RS25 in

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭353Statisticson | off (Default value: off)Shows the statistics results.Assignmenton | of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭21Methods or determinations can be signed at Level 2 in the Signature L

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭354￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)undone with a double-click on the section of the graph or with the context-

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭355The display of the measuring points in the table can be defined per windowand per com

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭356￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop command (only Titrando)The running STAT command was quit, then the nex

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭357NoteWhen the dialog window is opened, those Command type will be selec-ted as standar

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭358￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)For BRC commandsSelectionTime [s] | Measured value | Amount [µg] |Charge [m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭359LabelFreely definable axis label for the x axis. With auto the designation from thefi

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭360￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Autoscalingon | off (Default value: on)If this option is switched on then a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭361For MEAS T/Flow commandsSelectionTime [s] | Measured value | Flow [ml/min] | Cal-cula

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭362￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Only editable when autoscaling is disabled.Range-1.00E+12 ... +1.00E+12 Def

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭363SmoothingSmoothingon | off (Default value: on)Switches smoothing on/off for the curve

2.3 Electronic signatures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭22￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Sign]Sign method or determination. The window remains open.NoteMethods

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭364￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Autoscalingon | off (Default value: on)If this option is switched on then a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭365For MEAS T/Flow commandsSelectionTime [s] | Measured value | Flow [ml/min] | Cal-cula

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭366￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selection13 colors | pinkDefault valuepinkSymbolSelection of the symbol for

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3674.8.4.5 Curve properties - OptionsDialog window: Database ▶ Curves ▶ Properties curv

4.8 Curves subwindow￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭368￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)BackgroundBackground colorSelection of the color for the curve background.S

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4 Databasetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3694.8.4.6 Curve properties - Measuring point listDialog window: Database ▶ Curves ▶ Pr

5.1 Method - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭370￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5 Method5.1 Method - General5.1.1 Method - Definition Program part: Me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭371further modifications. Methods are stored in the configuration data-base and globally a

5.1 Method - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭372￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.1.3.2 Method - Menu FileProgram part: MethodNew… Create a new method (se

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭373Insert Inserts the content of the clipboard (commands, tracks) above the selected com-m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭23NoteSignatures 2 can only be deleted if the user belongs to a user gr

5.1 Method - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭374￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SaveSave the selected method (see Chapter 5.2.6, page 385).CloseClose the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭375Split horizontally Splits method window horizontally and display two methods below each

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭376￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.2 Method editor5.2.1 Creating new methodMenu item: Method ▶ File ▶ New…Wit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭377NameName of the method.SavedDate and time when the method was saved.UserShort name of t

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭378￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)program; the number of currently opened methods is displayed in the leftupper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3795.2.3.1 Display single methodMenu item: Method ▶ View ▶ UnsplitIn the default settings

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭380￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionFit to windowAdjust to both height and width of the window.5.2.4 Edi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3815.2.4.1.3 Move trackProgram part: Method ▶ Method windowMove track with Drag&DropT

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭382￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.2.4.1.5 Cut trackMenu item: Method ▶ Edit ▶ CutThe selected track is moved

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭383￭ ProcessLabDIGITAL IN, DIGITAL OUT, ANALOG IN, ANALOG OUT, STEPPINGMOTOR, PORTThe new

TeachwareMetrohm AGCH-9101 [email protected] documentation is protected by copyright. All rights reserved.Although all the information

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭24￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ timeTime indications must always be made with the aid of the Time( ) func-ti

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭384￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.2.4.2.5 Cut commandMenu item: Method ▶ Edit ▶ CutThe selected commands are

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭385Command without comment Command with comment5.2.5 Checking methodMenu item: Method ▶ F

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭386￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)comment) the table can be sorted according to the selected column inincreasing

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭387NoteThe method name must be unique in the whole Client/Server system.[Save]Save the sel

5.2 Method editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭388￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.2.8 Print method reportMenu item: Method ▶ File ▶ Print (PDF)…With menu ite

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3895.3 Managing methods5.3.1 Managing methodsDialog window Method ▶ File ▶ Method manage

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭390￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SignedDisplay if and at which level the method has been signed.Selectionno

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭391Show signatures…Show all signatures of the selected method (see Chapter 5.3.10.4, page

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭392￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Method groupSelection of the method group to which the selected methods sho

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3935.3.7 Exporting a methodMenu item: Method ▶ File ▶ Method manager... ▶ Method man-ager

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭25-2.38 yields -2.4-2.45 yields -2.5StatisticsThe mean value, absolute

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭394￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe method name must be unique in the whole Client/Server system.Locked

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭3955.3.10.2 Signature Level 1Dialog window:Database ▶ Determinations ▶ Sign ▶ Signature1.

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭396￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ReasonSelection from the Default reasons defined in the Security Settings d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭397Signature 2 not possible (signature 1 missing)The selected method or determination cann

5.3 Managing methods￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭398￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Signature dateDate and time at which the method was signed.UserShort name o

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭399[Delete]Delete Signatures 2.NoteSignatures 2 can only be deleted if the user belongs to

5.4 Method groups￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭400￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Make current]Restores the selected method version as the current method versi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭401[Delete]Deleting the selected method group.5.4.2 Edit method groups5.4.2.1 Method gro

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭402￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThe user group Administrators always has both access rights, i.e. theycannot be d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭403PresentationThe individual tracks are arranged side by side in the method window. Thetr

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭26￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The number of significant digits has now been reduced by three to four digitsb

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭404￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.5.2.2 Normal trackSubwindow: MethodA normal track is a track that can be created m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭405￭ Parallel running normal trackIf the check box Return immediately in the (see Chapter

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭406￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.5.2.4 Series end trackSubwindow: MethodA series end track is a track that can be c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4075.5.2.5 Exit trackSubwindow: MethodAn exit track is a track that can be created manual

5.5 Tracks￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭408￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The error track is executed if the determination is stopped due to an error.In this c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4095.6 Commands5.6.1 Commands - General5.6.1.1 Definition and PresentationSubwindow: Me

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭410￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ GreenTitration and measurement commands￭ YellowSample Processor and dosing comman

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭411￭ CALCCalculation of intermediate and end results, titer values and commonvariables.￭ C

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭412￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ METMonotonic Equivalence Point Titrations.￭ MOVEMoving to a rack position or an e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭413￭ STEPPING MOTORStandard addition with manual addition of the standard addition solu-ti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭27Name Syntax DescriptionCommonvariables'CV.Variablename.Variablei

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭414￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command START are configured on the following3 tab

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭415Identification DescriptionSample position.VAL Value of 'Sample position' (Num

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭416￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionMain track | Selection of available tracksDefault valueMain trackLive disp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭417track with the conditioning command. This parameter must be switched offfor automation

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭418￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Delete]Deletes the method variable selected in the table.5.6.2.2.5 START - Method

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭419Fixed valueon | off (Default value: off)If this option is enabled, then the method vari

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭420￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Lower limitLower limit for the variable.Type = NumberInput10 digitsType = Date/Time

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭421Message by E-mailon | off (Default value: off)If this option is enabled, the message de

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭422￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.2.2.6 Send E-mailDialog window: Send E-mailUse E-mail templateon | off (Defaul

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭423Mail fromE-Mail address of the sender.Input200 charactersSMTP serverAddress of SMTP mai

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭28￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Variable name Description Data type.OVFExceeding limits for methodvariable (Nu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭424￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Delete old dataon | off (Default value: off)All data previously generated by a trac

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭425Command variablesThe following command variables are generated in the method run by the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭426￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4275.6.2.7 ERRORDialog window: Method ▶ ERROR ▶ Properties.. ▶ ERROR 'Command name&a

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭428￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe END command does not have any parameters. It is created automati-call

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭429curve. An attempt is made to achieve constant measured value modificationswith each dos

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭430￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The figure shows that the evaluation also requires measuring points fromthe measuri

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4315.6.3.2.2 DET pH5.6.3.2.2.1 DET pH - OverviewDialog window: Method ▶ DET pH ▶ Propert

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭432￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.BP{x}.ERCERC or first derivative for the break point × (

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭433Identification Description.FIN Command status; 1 = Command has ended at leastonce, 0, i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭29NoteIn the case of variables with Index {x}, the desired number 1…9 m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭434￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.LP.TIMTime in s until the last measuring point in the me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭435Identification Description.TITERTiter value of the solution used for the command5.6.3.2

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭436￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭437SensorSelection of a sensor of type pH electrode from the list of sensors availablein t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭438￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Switch off automaticallyon | off (Default value: on)If this option is enabled, the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭439Min. waiting timeThe minimum waiting period is only important for drift-controlled meas

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭440￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Start measured valueNoteIs displayed only for Titrando and 855.Start measured value

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭441Range0.01 ... 166.00 mL/minDefault value5.00 mL/minSelectionmaximumPausePauseWaiting ti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭442￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measured value acceptanceNoteWill be displayed only if the User option is selected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭443Titrando, 855Range0.1 ... 999999 sDefault value38.0 (slow), 26.0 (optimal), 21.0 (fast)

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭30￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription Commands.BSY Command status; 1 = BUSY,HOLD or ERROR

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭444￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.1 ... 9999.9 µLSelectionoffDefault valueoffDosing rateSpeed at

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭445Conditions for stopping the titration. If more than one stop condition is ineffect at t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭446￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.01000 ... 9999.99 mLSelectionoffDefault valueoffStop timeStops

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭447Evaluation without windowWith this option set, the two parameters EP criterion and EP r

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭448￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ascendingOnly equivalence points with a positive slope of the titration curve willb

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4495.6.3.2.2.7 DET pH - Additional evaluationsTab: Method ▶ DET pH ▶ Properties... ▶ Addi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭450￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭451related to the total measured value alteration, even small changes in themeasured value

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭452￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = Measured value pHRange-20.0 ... 20.0 pHDefault value20.0 pHWindow = Volume

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭453Range-20.000 ... 20.000 Default value20.000 5.6.3.2.2.8 DET pH - Additional measured v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭31Identifica-tionDescription Commands.CYLCylinder volume of the exchang

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭454￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Opens the dialog window External measured value # in which theparameters for t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭455Titrando, 855Selectionfirst | greatest | last | ascending | descendingDefault valuefirs

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭456￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭457TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.2.3 DET U5.6.3.2.3.1

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭458￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Additional measured valuesDefinition of additional measured values of other measu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭459Identification Description.EP{x}.TIMTime in s until the endpoint × (1…9) is reached.EP{

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭460￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.LP.EXxExternal value × (1...3) for the last measuring po

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭461Identification Description.SVMStart volume measured value (volume which was addedaccord

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭462￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭463855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection o

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭32￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription Commands.EP{x}.DMEMeasured value differential for t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭464￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate cha

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭465SelectionoffDefault valueoffoffThe measured vales will not be applied until after the m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭466￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximumStart measure

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭467Dosing rateSpeed at which the start volume is added until the start slope is reached.Th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭468￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)fastFor less critical rapid titrations.UserEditing the individual titration paramet

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭469elapsed. If the waiting time has not been newly entered then a waiting timethat is suit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭470￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)if the change of direction in the potential jump region is very abrupt, asotherwise

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4715.6.3.2.3.5 DET U - Stop conditionsTab: Method ▶ DET U ▶ Properties... ▶ Stop conditio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭472￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionoffVolume after EPWhen the number of equivalence points defined under Stop

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭473Potentiometric evaluationSelectionEvaluation without window | Evaluation withmeasured v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭33Identifica-tionDescription Commands.FIN Command status; 1 = Commandha

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭474￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)greatestOnly the equivalence point with the greatest ERC value, i.e. the steepestju

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4755.6.3.2.3.7 DET U - Additional evaluationsTab: Method ▶ DET U ▶ Properties... ▶ Additi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭476￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭477related to the total measured value alteration, even small changes in themeasured value

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭478￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = Measured valueRange-2000.0 ... 2000.0 mVDefault value2000.0 mVWindow = Vol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4795.6.3.2.3.8 DET U - Additional measured valuesTab: Method ▶ DET U ▶ Properties... ▶ Ad

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭480￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window External measured value # in which theparameter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭481Titrando, 855Range0 ... 200 Default value5 EP recognitionFilter for the recognition of

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭482￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.00000 ... 9999.99 mLDefault value9999.99 mLEP criterionCriterio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭483Measured valueRange-2000.0 ... 2000.0 mVTimeRange0.0 ... 999999.9 sVolumeRange0.00000 .

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭IIITable of contents1 Introduction 11.1 Welcome to tiamo ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭34￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription Commands.GMAMaximum gas flow rate in mL/min MEAS T/

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭484￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Additional evaluationsDefinition of additional methods for the evaluation of the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭485Identification Description.ETEEnd temperature (temperature following processing ofthe c

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭486￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.LP.MEAMeasured value for the last measuring point in the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭487Identification Description.SVTTotal start volume (volume that was added in depend-ence

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭488￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrandoSelection1 | 2 | 3 | 4Default value1855Selection1 | 2 | 3Default value1Titr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭489Measuring inputSelection of the measuring input to which the sensor is connected.Titran

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭490￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)continuousA temperature sensor must be connected. The temperature will then bemeasu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭4915.6.3.2.4.3 DET Ipol - Start conditionsTab: Method ▶ DET Ipol ▶ Properties... ▶ Start

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭492￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 999999 sDefault value1 sStart volumeStart volumeVolume to be added befor

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭493Dosing rateSpeed at which the start volume is added until the start slope is reached.Th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭35Identifica-tionDescription Commands.LCOLoop counter = current quantit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭494￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.2.4.4 DET Ipol - Titration parametersTab: Method ▶ DET Ipol ▶ Properties...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭495Titrando, 855Range0.1 ... 999.0 mV/minDefault value20.0 (slow), 50.0 (optimal), 80.0 (f

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭496￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing of incrementsNoteThe following parameters will be displayed only if the User

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭497Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrinoRang

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭498￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.00000 ... 9999.99 mLDefault value100,000 mLSelectionoffTitrinoR

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭499Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with whic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭500￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Evaluation with measured value window (Upol)With this option set, up to 9 regions (

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭501descendingOnly equivalence points with a negative slope of the titration curve willbe r

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭502￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The following additional methods for evaluation of titration curves can beactivated

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭503Maximum evaluationMaximum evaluationon | off (Default value: off)If this option is enab

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭36￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription Commands.LP.MEAMeasured value for the last meas-uri

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭504￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range2 ... 20 Default value5 WindowA range (window) can be defined on the measured

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭505Gran evaluationNoteThis evaluation method is possible only with Titrando and 855.Gran e

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭506￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Additional calculated measured valuesAdditional calculated measured valueson | off

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭5075.6.3.2.4.9 DET Ipol - Measured value windowDialog window: Method ▶ DET Ipol ▶ Propert

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭508￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Selectionfirst | greatest | last | ascending | descendingDefault value

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭509EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered ERCv

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭510￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.2.5 DET Upol5.6.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭511￭ Additional measured valuesDefinition of additional measured values of other measuring

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭512￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab).ETEEnd temperature (temperature following processing ofthe command) in °C.EVTEnd v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭513.LP.TEMTemperature for the last measuring point of the meas-uring point list in °C.LP.T

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭37Identifica-tionDescription Commands.MA.MEAMaximum measured value in t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭514￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.2.5.2 DET Upol - General/HardwareTab: Method ▶ DET Upol ▶ Properties... ▶ Ge

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭515855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectionint

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭516￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)U(pol)The polarization voltage is the potential applied to the polarized electroded

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭517offNo stirrer will be used.Stirring rateSetting the stirring rate. The algebraic sign o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭518￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.01 ... 99.90 µA/minDefault value20.00 (slow), 50.00 (optimal),

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭519TitrinoRange0.00 ... 999.99 mLDefault value0.00 mLDosing rateSpeed at which the start v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭520￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Start slopeNoteIs displayed only for Titrando and 855.Start slopeWhen the start slo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭521Titration rateTitration rateThe three predefined sets of parameters can be selected for

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭522￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0.05 ... 99.90 µA/minDefault value20.00 (slow), 50.00 (optimal), 80.00

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭523Measuring point densityA small value means small volume increments, i.e. a high measuri

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭38￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription Commands.MR.MRCCorrelation coefficient for meandosi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭524￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionmaximumDefault valuemaximumTemperatureTemperatureManually entered titratio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭525Stop measured valueStops when the preset value for a measuring point has been exceeded

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭526￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionmaximumDefault valuemaximum5.6.3.2.5.6 DET Upol - Potentiometric evaluati

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭527EP recognitionFilter for the recognition of equivalence points:TitrinoSelectionall | gr

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭528￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Delete]Deletes the window selected in the table.Evaluation with volume window (mL)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭529[Properties]Opens the dialog window Fix endpoint evaluation # to edit the fixedendpoint

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭530￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Break-point evaluationon | off (Default value: off)A break-point evaluation is used

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭531Window = TimeRange0 ... 999999 sDefault value0 sUpper limitValue for the upper limit of

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭532￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Upper limitValue for the upper limit of the Gran evaluation range.Range-200.0 ... 2

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭533can also be displayed in curves under the designation Extern 1…3 and usedin formulas as

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭39Identifica-tionDescription Commands.RANCurrent, absolute rotation ang

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭534￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Selectionfirst | greatest | last | ascending | descendingDefault value

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭535EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered ERCv

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭536￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.3 MET5.6.3.3.1

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭537VEP = EP volume, V0 = total volume added before ∆n, ∆V = volume incre-ment,ρ = interpol

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭538￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command MET pH are configured in the following7 ta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭539Identification Description.DSCTime for processing all start conditions s.EMEEnd measure

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭540￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.HP{x}.MEAMeasured value for the HNP × (1…9) in mV (HNP =

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭541Identification Description.MI.TIMTime for the minimum measured value in s.MI.VOLVolume

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭542￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selection'Device name' | not definedDefault valuenot definednot definedIn

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭543of the working life, the validity of the titer and the GLP test interval for theselecte

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭40￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription Commands.SPOCurrent external position (entrywhen en

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭544￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)offThe temperature will not be measured. The temperature entered man-ually under Te

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭545Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭546￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.00000 ... 9999.99 mLDefault value0.00000 mLTitrinoRange0.00 ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭547SelectionmaximumStart slopeNoteIs displayed only for Titrando and 855.Start slopeWhen t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭548￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titration rateTitration rateThe three predefined sets of parameters can be selected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭549TitrinoRange0.5 ... 999.0 mV/minDefault value20.0 (slow), 50.0 (optimal), 80.0 (fast) m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭550￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Volume incrementSmall volume increments are used for the determination of blank val

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭551TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °C5.6.3.3.2.5 MET pH - Stop condition

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭552￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop EPThe titration is stopped when the specified number of equivalence pointshas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭5535.6.3.3.2.6 MET pH - Potentiometric evaluationTab: Method ▶ MET pH ▶ Properties... ▶ P

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭41Identifica-tionDescription Commands.TC.C4Coefficient of the Chebyshev

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭554￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)EP recognitionFilter for the recognition of equivalence points:TitrinoSelectionall

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭555[Properties]Opens the dialog window Volume window # in which the parameters forthe sele

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭556￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)pK/HNP evaluationpK/HNP evaluationon | off (Default value: off)If this option is en

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭557Break-point evaluationon | off (Default value: off)A break-point evaluation is used to

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭558￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = TimeRange0 ... 999999 sDefault value0 sUpper limitValue for the upper limi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭559Lower limit pHValue for the lower limit of the Gran evaluation range.Range-20.000 ... 2

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭560￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Additional external measured valuesAdditional external measured valueson | off (Def

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭561Titrando, 855Range0.1 ... 9.99 Default value0.50 EP recognitionFilter for the recogniti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭562￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.00000 ... 9999.99 mLDefault value9999.99 mLEP criterion pHCrite

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭563Fix valueValue of the fix endpoint.Measured valueRange-20.000 ... 20.000 pHTimeRange0.0

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭42￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.3.4 Result variablesDialog window: Formula Editor ▶ VariablesResult varia

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭564￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Potentiometric evaluationParameters for the potentiometric evaluation of titratio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭565.EP{x}.MEP Quantity of endpoints in the window × (1…9); 1 = 1endpoint, 2 = 2 or more en

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭566￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab).ITEInitial temperature (temperature before start conditionsare processed) in °C.LP

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭567.STYType of stop with which the command was stopped:1 = normal;0 = manual or after erro

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭568￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭569855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelection o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭570￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stirring rateSetting the stirring rate. The algebraic sign of the stirring rate cha

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭571SelectionoffDefault valueoffoffThe measured vales will not be applied until after the m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭572￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximumStart measure

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭573Dosing rateSpeed at which the start volume is added until the start slope is reached.Th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭43Syntax'DV.Variable name'Examples: 'DV.DUR', &apos

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭574￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)fastFor less critical rapid titrations.UserEditing the individual titration paramet

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭575elapsed. If the waiting time has not been newly entered then a waiting timethat is suit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭576￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrino

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭577Titrando, 855Range0.00000 ... 9999.99 mLDefault value100,000 mLSelectionoffTitrinoRange

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭578￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭579Evaluation with measured value window (U)With this option set, up to 9 regions (windows

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭580￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)descendingOnly equivalence points with a negative slope of the titration curve will

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭581Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this opti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭582￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭583related to the total measured value alteration, even small changes in themeasured value

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭IV￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.5 Molar mass calculator ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭44￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Variable name Description DatatypeSTCStart counter NumberUSNShort name of the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭584￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = Measured valueRange-2000.0 ... 2000.0 mVDefault value2000.0 mVWindow = Vol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭5855.6.3.3.3.8 MET U - Additional measured valuesTab: Method ▶ MET U ▶ Properties... ▶ Ad

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭586￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window External measured value # in which theparameter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭587EP recognitionFilter for the recognition of equivalence points:Titrando, 855Selectionfi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭588￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)EP criterionCriterion for the recognition of endpoints. Endpoints whose discovered

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭589TimeRange0.0 ... 999999.9 sVolumeRange0.00000 ... 9999.99 mL5.6.3.3.4 MET Ipol5.6.3.3.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭590￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Additional measured valuesDefinition of additional measured values of other measu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭591Identification Description.ETEEnd temperature (temperature following processing ofthe c

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭592￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.LP.EXxExternal value × (1...3) for the last measuring po

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭593Identification Description.SVSStart volume slope (volume that was added accordingto the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭45Overview of the operators and functionsOperators FunctionsArithmetic:

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭594￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭595855, 888Selection1Default value1SensorSelection of a sensor of type Metal electrode fro

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭596￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)offThe temperature will not be measured. The temperature entered man-ually under Te

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭597Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭598￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.00000 ... 9999.99 mLDefault value0.00000 mLTitrinoRange0.00 ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭599SelectionmaximumStart slopeNoteIs displayed only for Titrando and 855.Start slopeWhen t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭600￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titration rateThe three predefined sets of parameters can be selected for the titra

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭601offMeasured value acceptance will take place after the maximum waitingtime has elapsed.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭602￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)as the measured value alterations between two measuring points are thenof the same

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6035.6.3.3.4.5 MET Ipol - Stop conditionsTab: Method ▶ MET Ipol ▶ Properties... ▶ Stop co

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭46￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.2 Arithmetical operators2.4.4.2.1 AdditionDialog window: Formula edito

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭604￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionoffVolume after EPWhen the number of equivalence points defined under Stop

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭605Potentiometric evaluationSelectionEvaluation without window | Evaluation withmeasured v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭606￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)allAll equivalence points will be recognized.greatestOnly the equivalence point wit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭607[Delete]Deletes the window selected in the table.5.6.3.3.4.7 MET Ipol - Additional eva

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭608￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Threshold valueThe evaluation of the minimum begins as soon as the slope of the cur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭609SlopeMinimum difference between the slope before and after the break-point.The smaller

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭610￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = TimeRange0 ... 999999 sDefault value999999 sGran evaluationNoteThis evalua

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭611Additional calculated measured valuesAdditional calculated measured valueson | off (Def

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭612￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.3.4.9 MET Ipol - Measured value windowDialog window: Method ▶ MET Ipol ▶ Pro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭613firstOnly the first endpoint to be found will be recognized.greatestOnly the endpoint w

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭472.4.4.2.2 SubtractionDialog window: Formula editor ▶ Operators/Funct

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭614￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)EP recognitionFilter for the recognition of equivalence points:Titrando, 855Selecti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6155.6.3.3.5 MET Upol5.6.3.3.5.1 MET Upol - OverviewDialog window: Method ▶ MET Upol ▶ P

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭616￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.BP{x}.DMEMeasured value differential for the break point

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭617Identification Description.FP{x}.DMEMeasured value differential for the fixed endpoint

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭618￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.LP.TIMTime in s until the last measuring point in the me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6195.6.3.3.5.2 MET Upol - General/HardwareTab: Method ▶ MET Upol ▶ Properties... ▶ Genera

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭620￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭621U(pol)The polarization voltage is the potential applied to the polarized electrodedurin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭622￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)offNo stirrer will be used.Stirring rateSetting the stirring rate. The algebraic si

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭623Measured value driftThe measured value is only accepted if the drift is less than the v

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭48￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ExamplesOperand1 Operand2 Result Example RemarkOperands of the same type:Numbe

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭624￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrino

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭625Start slopeWhen the start slope is reached the dosing of the start volume is stoppedand

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭626￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)slowFor titrations in which the finest details are also to be visible. This couldho

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭627has elapsed, even if the signal drift has already been reached. The drift con-tinues to

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭628￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0.001 ... 9.999 mLDefault value0.05 (slow), 0.10 (optimal), 0.20 (fast)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭629Conditions for stopping the titration. If more than one stop condition is ineffect at t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭630￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭631Evaluation with measured value window (Upol)With this option set, up to 9 regions (wind

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭632￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)descendingOnly equivalence points with a negative slope of the titration curve will

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭633The following additional methods for evaluation of titration curves can beactivated and

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭49Operand1 Operand2 Result Example RemarkOperand of different type: The

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭634￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Maximum evaluationMaximum evaluationon | off (Default value: off)If this option is

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭635Range2 ... 20 Default value5 WindowA range (window) can be defined on the measured valu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭636￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Gran evaluationNoteThis evaluation method is possible only with Titrando and 855.Gr

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭637Additional calculated measured valuesAdditional calculated measured valueson | off (Def

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭638￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.3.5.9 MET Upol - Measured value windowDialog window: Method ▶ MET Upol ▶ Pro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭639descendingOnly endpoints with a negative slope of the titration curve will be rec-ogniz

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭640￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)greatestOnly the endpoint with the greatest ERC value, i.e. the steepest jump,will

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭641or after a waiting period. The volume that has been added when the end-point is reached

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭642￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteThis command is used for rapid routine determinations when the endpointdoes not

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6435.6.3.4.3 SET pH5.6.3.4.3.1 SET pH - OverviewDialog window: Method ▶ SET pH ▶ Propert

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭50￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Operand1 Operand2 Result Example RemarkTime Number NumberTime(1999;10;7) ^ 2.5

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭644￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Additional measured valuesDefinition of additional measured values of other measu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭645Identification Description.ETEEnd temperature (temperature following processing ofthe c

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭646￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.MA.VOLVolume with maximum measured value in mL.MI.MEAMin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭647Selection'Device name' | not definedDefault valuenot definednot definedIn thi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭648￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)of the working life, the validity of the titer and the GLP test interval for thesel

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭649offThe temperature will not be measured. The temperature entered man-ually under Temper

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭650￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Initial measured valueNoteIs displayed only for Titrando and 855.The initial measur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭651Titrando, 719, 720, 736, 751, 758, 785, 794, 798, 799Range0 ... 999999 sDefault value0

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭652￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.4.3.4 SET pH - Control parametersTab: Method ▶ SET pH ▶ Properties... ▶ Cont

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭653ControlNoteWill be displayed only if the User option is selected in the Titrationrate l

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭51Oper-and1Oper-and2Result Example RemarkNumber Text Number1.2 AND &quo

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭654￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭655TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stopped

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭656￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.4.3.5 SET pH - Titration parametersTab: Method ▶ SET pH ▶ Properties... ▶ Ti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭657TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °CTime interval measuring pointTime in

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭658￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭659Drift correctionIf this parameter is set to automatic or manual the drift correction (

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭660￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 999 sDefault value0 sSample addition timeWaiting time between stop of co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭661Moves the selected line up (changes the sequence).Moves the selected line down (changes

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭662￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.4.3.9 SET pH - Additional measured valuesTab: Method ▶ SET pH ▶ Properties..

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭663[Properties]Opens the dialog window External measured value # in which theparameters fo

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭52￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Operand1 Operand2 Result Example RemarkNumber Number Number5 OR 4 --> 14 OR

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭664￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)AppearanceThe command has the following appearance:without conditioning with condit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭665Identification Description.CBY Command status; 1 = Conditioning activated, 0 =Condition

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭666￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.FP{x}.TIMTime in s until the fixed endpoint × (1…9) is r

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭667Identification Description.SLOElectrode slope of the sensor used for the command (inmV

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭668￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)If the option not defined is selected as Device name, any device types ordevice gro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭669SensorMeasuring inputSelection of the measuring input to which the sensor is connected.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭670￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)StirrerStirrerSelection of the stirrer.Titrando, 855Selection1 | 2 | 3 | 4 | offoff

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭671Initial measured valueNoteIs displayed only for Titrando and 855.The initial measured v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭672￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 719, 720, 736, 751, 758, 785, 794, 798, 799Range0 ... 999999 sDefault val

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6735.6.3.4.4.4 SET U - Control parametersTab: Method ▶ SET U ▶ Properties... ▶ Control pa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭53The operands can be entered either directly or as a variable and can

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭674￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ControlNoteWill be displayed only if the User option is selected in the Titrationra

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭675Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast) µL/m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭676￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stop

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6775.6.3.4.4.5 SET U - Titration parametersTab: Method ▶ SET U ▶ Properties... ▶ Titratio

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭678￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °CTime interval measuring pointTim

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭679Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with whic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭680￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Drift correctionIf this parameter is set to automatic or manual the drift correctio

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭681Range0 ... 999 sDefault value0 sSample addition timeWaiting time between stop of condit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭682￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Moves the selected line up (changes the sequence).Moves the selected line down (cha

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭6835.6.3.4.4.9 SET U - Additional measured valuesTab: Method ▶ SET U ▶ Properties... ▶ Ad

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭V3.8.3 Live display - Application note ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭54￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.4.2 Greater thanDialog window: Formula editor ▶ Operators/FunctionsSynt

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭684￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window External measured value # in which theparameter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭685AppearanceThe command has the following appearance:without conditioning with conditioni

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭686￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.COK Command status; 1 = Condition requirement ful-filled

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭687Identification Description.IMEInitial measured value (measured value before startcondit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭688￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.STEStart temperature (temperature after processing of th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭689Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or excha

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭690￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)855, 888Selection1Default value1SensorSelection of a sensor of type Metal electrode

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭691offThe temperature will not be measured. The temperature entered man-ually under Temper

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭692￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Initial measured valueNoteIs displayed only for Titrando and 855.The initial measur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭693Titrando, 719, 720, 736, 751, 758, 785, 794, 798, 799Range0 ... 999999 sDefault value0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭552.4.4.4.3 Greater than or equal toDialog window: Formula editor ▶ Op

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭694￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.4.5.4 SET Ipol - Control parametersTab: Method ▶ SET Ipol ▶ Properties... ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭695ControlNoteWill be displayed only if the User option is selected in the Titrationrate l

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭696￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭697TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stopped

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭698￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.4.5.5 SET Ipol - Titration parametersTab: Method ▶ SET Ipol ▶ Properties...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭699TitrinoRange-170.0 ... 500.0 °CDefault value25.0 °CTime interval measuring pointTime in

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭700￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range0 ... 999999 sSelectionoffDefault valueoffFilling rateSpeed with

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭701Drift correctionIf this parameter is set to automatic or manual the drift correction (

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭702￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 999 sDefault value0 sSample addition timeWaiting time between stop of co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭703Moves the selected line up (changes the sequence).Moves the selected line down (changes

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭56￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.4.4 Less than Dialog window: Formula editor ▶ Operators/FunctionsSyntax

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭704￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.4.5.9 SET Ipol - Additional measured valuesTab: Method ▶ SET Ipol ▶ Properti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭705[Properties]Opens the dialog window External measured value # in which theparameters fo

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭706￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)AppearanceThe command has the following appearance:without conditioning with condit

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭707Identification Description.COK Command status; 1 = Condition requirement ful-filled, 0

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭708￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.IMEInitial measured value (measured value before startco

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭709Identification Description.SMEStart measured value (measured value after processingthe

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭710￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionDevice types | TitrandoDefault valueTitrandoDosing deviceDosing deviceSele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭711TitrandoSelection1 | 2Default value1855, 888Selection1Default value1SensorSelection of

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭712￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)automaticIf a temperature sensor is connected then the temperature will be meas-ure

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7135.6.3.4.6.3 SET Upol - Start conditionsTab: Method ▶ SET Upol ▶ Properties... ▶ Start

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭572.4.4.4.5 Less than or equal to Dialog window: Formula editor ▶ Oper

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭714￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 999999 sDefault value1 sPause 1Pause 1Waiting time, e.g. until the elect

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭715Pause 2Pause 2Waiting time, e.g. for the electrode to settle down after the start or a

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭716￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)UserEditing the individual titration parameters which affect the titration rate.Con

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭717Range0.01 ... 9999.00 µL/minDefault value5.00 (slow), 25.00 (optimal), 50.00(fast) µL/m

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭718￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0 ... 999 sDefault value10 sSelectioninf.Stop timeThe titration is stop

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭719Titration directionSelection of the titration direction. If two endpoints are set, then

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭720￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0.08 ... 16200 sDefault value2.00 s5.6.3.4.6.6 SET Upol - Stop conditi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭721Titrando, 855Range0.01 ... 166.00 mL/minSelectionmaximumDefault valuemaximumTitrinoRang

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭722￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)offNo drift correction takes place.Drift valueDrift value for drift correction. Thi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭723Only start titration by a start command from a SEND commandon | off (Default value: off

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭58￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.4.6 Not equal to Dialog window: Formula editor ▶ Operators/FunctionsSyn

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭724￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Opens the dialog window Fix endpoint evaluation # to enter a new fixedendpoint

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7255.6.3.4.6.9 SET Upol - Additional measured valuesTab: Method ▶ SET Upol ▶ Properties..

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭726￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window External measured value # in which theparameter

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭727Reagent addition takes place in three phases during the titration:￭ Initial dosingDurin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭728￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ KFT UpolAmperometric measurement with selectable polarization voltage (meas-ured

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭729￭ Additional measured valuesDefinition of additional measured values of other measuring

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭730￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.EVTEnd volume (total dosed volume at the end of the com-

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭731Identification Description.MI.TEMTemperature with minimum measured value in °C.MI.TIMTi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭732￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device typeDisplay or selection of the device type. If a device is selected under D

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭733not definedNo tests will be carried out.SensorMeasuring inputSelection of the measuring

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭592.4.4.5 Arithmetical functions2.4.4.5.1 Exponential functionDialog

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭734￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)continuousA temperature sensor must be connected. The temperature will then bemeasu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7355.6.3.5.2.3 KFT Ipol - Start conditionsTab: Method ▶ KFT Ipol ▶ Properties... ▶ Start

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭736￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 999999 sDefault value1 sPause 1Pause 1Waiting time, e.g. until the elect

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭737Range0 ... 999999 sDefault value0 s5.6.3.5.2.4 KFT Ipol - Control parametersTab: Metho

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭738￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ControlNoteWill be displayed only if the User option is selected in the Titrationra

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭739Range0.1 ... 9.9 µL/minDefault valueminimum (slow), minimum (optimal), 5.0(fast) µL/min

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭740￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Relative stop driftThe titration is stopped when the endpoint and the stop drift ha

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭741Selection+ | - | autoDefault valueauto+positive measured value alteration-negative meas

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭742￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.5.2.6 KFT Ipol - Stop conditionsTab: Method ▶ KFT Ipol ▶ Properties... ▶ Sto

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭743TitrinoRange0.01 ... 150.00 mL/minSelectionmaximumDefault valuemaximum5.6.3.5.2.7 KFT

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭60￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.5.3 Common logarithmDialog window: Formula editor ▶ Operators/Functions

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭744￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Drift valueDrift value for drift correction. This parameter is only shown for Drift

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭745NoteConditioning must already be completed (= Condok) at the time theSEND command is re

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭746￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Delete]Deletes the selected line.Minimum evaluationMinimum evaluationon | off (Def

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭747Additional calculated measured valuesAdditional calculated measured valueson | off (Def

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭748￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.5.2.10 KFT Ipol - Fix endpoint evaluation Dialog window: Method ▶ KFT Ipol

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭749ParametersThe parameters for the command KFT Upol are configured in the following8 tabs

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭750￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.DRICurrent and/or last drift for drift correction in µL/

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭751Identification Description.LP.EXxExternal value × (1...3) for the last measuring point

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭752￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.5.3.2 KFT Upol - General/HardwareTab: Method ▶ KFT Upol ▶ Properties... ▶ Ge

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭753855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectionint

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭612.4.4.5.5 Absolute valueDialog window: Formula editor ▶ Operators/Fu

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭754￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)U(pol)The polarization voltage is the voltage applied to the polarized electrodedur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭755offNo stirrer will be used.Stirring rateSetting the stirring rate. The algebraic sign o

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭756￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measured value driftThe measured value is only accepted if the drift is less than t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭757TitrinoRange0.00 ... 999.99 mLDefault value0.00 mLDosing rateSpeed at which the start v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭758￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titration rateTitration rateThe three predefined sets of parameters can be selected

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭759Max. rateRate at which dosing is carried out outside of the Control range. The max-imum

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭760￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)timeThe endpoint must be exceeded for a certain time: the Delay time. Thesame Delay

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭761Stop timeThe titration is stopped if the absolute stop time defined here has elapsedsin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭762￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range-20.0 ... 150.0 °CDefault value25.0 °CTitrinoRange-170.0 ... 500.

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭763Stop timeTitrandoRange0 ... 999999 sSelectionoffDefault valueoffoffStops when the prese

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭62￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.5.7 IntegerDialog window: Formula editor ▶ Operators/FunctionsSyntaxy =

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭764￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrandoRange1 ... 999 µg/minDefault value20 µg/minDrift correctionIf this paramete

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭765Stabilizing timeWaiting period until the start of the titration during which the condit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭766￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭767Maximum evaluationMaximum evaluationon | off (Default value: off)If this option is enab

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭768￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Delete]Deletes the calculated measured value selected in the table.Additional exte

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7695.6.3.6 KFC5.6.3.6.1 KFC - OverviewDialog window: Method ▶ KFC ▶ Properties.. ▶ KFC -

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭770￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Additional evaluationsDefinition of additional methods for the evaluation of the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭771Identification Description.FP{x}.MEAMeasured value for the fixed endpoint × (1…9) in th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭772￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.NMPNumber of measuring points in the measuring point lis

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭773SensorSensorSelection of a sensor of type Metal electrode from the sensors configuredin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭632.4.4.5.9 SignDialog window: Formula editor ▶ Operators/FunctionsSyn

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭774￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)offThe temperature will not be measured. The temperature entered man-ually under Te

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭775851, 852Selection1 | 2 | 3 | 4 | offDefault value1offNo stirrer will be used.Stirring r

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭776￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)End pointEP atMeasured value for the endpoint.756, 831Range-2000.0 ... 2000.0 mVDef

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭777DynamicsThe control range is entered as distance to the endpoint. Within the controlran

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭778￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Ipol 10 µA 20 µA 30 µAEP 50 mV 100 mV 150 mVDynamics 70 mV 100 mV 120 mVMax. rateMa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭779Range1 ... 999 µg/minDefault value5 µg/minRelative stop driftThe titration is stopped w

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭780￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Time interval measuring pointTime interval for entering a measuring point in the me

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭781Run subwindow displayed on the Single determination or Determina-tion series tab will t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭782￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0 ... 99 sDefault value0 sAutomatic start after sample additionon | off (Defau

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7835.6.3.6.8 KFC - Additional evaluationsTab: Method ▶ KFC ▶ Properties... ▶ Additional e

Table of contents￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭VI￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)4.6.5 Information - Configuration ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭64￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Type number, value range: 1 ... n. Direct entry as number or as formulaprovidi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭784￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Additional calculated measured valuesAdditional calculated measured valueson | off

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭7855.6.3.6.10 KFC - Fix endpoint evaluation Dialog window: Method ▶ KFC ▶ Properties...

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭786￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command BRC are configured in the following 8tabs:

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭787Identification Description.EMEEnd measured value (measured value after processingof the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭788￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.LP.IGECurrent pulsed current for the last measuring poin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭789Device typeDisplay or selection of the device type. If a device is selected under Devic

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭790￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)continuousA temperature sensor must be connected. The temperature will then bemeasu

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭791Switch on/off automaticallyon | off (Default value: on)If this option is enabled, the s

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭792￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Max. waiting timeIf signal drift has been switched off or has not yet been reached,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭793optimalParameter set for all standard titrations; optimized for the most frequentapplic

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭65NoteUTC = Universal Time , from which the times in the various time z

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭794￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range1.0 ... 999.0 µg/minDefault value15.0 (slow), 25.0 (optimal), 50.0 (fast) µg/m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭795Extraction timeThe titration is not stopped until the extraction time has elapsed (even

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭796￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Conditioningon | off (Default value: on)Enable/Disable the conditioning. If the con

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭797Stabilizing timeWaiting period until the start of the titration during which the condit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭798￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭799[New]Opens the dialog window Calc. measured value # in which the parame-ters for the ad

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭800￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Fix valueValue of the fix endpoint.Measured valueRange-2000.0 ... 2000.0 mVTimeRang

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭801CommandsDepending on the measured value, one of the following twoSTAT com-mands can be

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭802￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.8.3 STAT - Evaluation windowDialog window: Method ▶ STAT ▶ Properties... ▶ E

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭803Limit exceedingSelects the exceeded limit for which a track is to be started.SelectionL

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭66￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteUTC = Universal Time , from which the times in the various time zones ofth

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭804￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Cylin-der vol-umeMax. dosing rate Max. flow rate ExchangeunitDosingunitExchangeuni

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭805￭ General/HardwareParameters for devices, dosing devices, sensors and stirrers.￭ Start

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭806￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.FIN Command status; 1 = Command has ended at leastonce,

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭807Identification Description.MI.TEMTemperature with minimum measured value in °C.MI.TIMTi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭808￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.8.6.2 STAT pH - General/HardwareTab: Method ▶ STAT pH ▶ Properties... ▶ Gene

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭809855Selection1 | 2 | 3Default value1TitrinoSelectioninternal D0736, 751, 799Selectionint

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭810￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SolutionInput of a solution name or selection of a solution from the solutions defi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭811SensorSelection of a sensor of type pH electrode from the list of sensors availablein t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭812￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Switch off automaticallyon | off (Default value: on)If this option is enabled, the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭813Min. waiting timeThe minimum waiting period is only important for drift-controlled meas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭67NoteOnly the integral part is used for all parameters.A variable of t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭814￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionmaximumDefault valuemaximumTitrinoRange0.01 ... 150.00 mL/minSelectionmaxi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭815Selection50 µL/min | 100 µL/min | 500 µL/min | UserDefault value100 µL/minControlNoteWi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭816￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Min. rateRate at which dosing is carried out at the very beginning of the titration

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭817-negative measured value alterationautoThe titration direction is determined automatica

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭818￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionoffDefault valueoffTitrinoRange-20.00 ... 20.00 SelectionoffDefault valueo

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭819TitrinoRange0.000 ... 9999.99 mLDefault value100.00 mLSelectionoffStop timeStops when t

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭820￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Filling rateSpeed with which the dosing cylinder is to be refilled after the titrat

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭821Lower hysteresis pHLower hysteresis of the measured value. If the measured value exceed

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭822￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Wait for [Continue]Reagent dosing in the current STAT command is interrupted and a

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭823Titrando, 855Range0.00 ... 166.00 mL/minDefault value166.00 mL/minTitrinoRange0.00 ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭68￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ExamplesNumberToText(-55.3) = -55.3NumberToText('CV.AverageTemp') =

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭824￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)NoteIf, when monitoring the dosing rate, the Lower limit is exceeded thenthe action

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭825TitrinoRange-170.0 ... 500.0 °CDefault value500.0 °CUpper hysteresisUpper hysteresis of

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭826￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window Track call # in which the parameters for thetra

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭827Moves the selected line down (changes the sequence).[New]Opens the dialog window Fix en

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭828￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.8.6.9 STAT pH - Additional measured valuesTab: Method ▶ STAT pH ▶ Properties

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭829[Properties]Opens the dialog window External measured value # in which theparameters fo

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭830￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command STAT U are configured in the following8 ta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭831Identification Description.EMEEnd measured value (measured value after processingof the

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭832￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.MA.MEAMaximum measured value in the unit of the measured

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭833Identification Description.SVAStart volume absolute (volume that was added accord-ing t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭69TextToNumber('CV.DurchschnTemp') = Value of the variables (

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭834￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Dosing deviceDosing deviceSelection of the number of the dosing device (dosing or e

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭835Dosing deviceSelection of the number of the dosing device (dosing or exchange unit) tob

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭836￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrandoSelection1 | 2Default value1855Selection1Default value1TitrinoSelection1 |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭837Titrando, 855Selection1 | 2 | 3 | 4 | offoffNo stirrer will be used.Stirring rateSettin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭838￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measured value driftThe measured value is only accepted if the drift is less than t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭839TitrinoRange0.00 ... 999.99 mLDefault value0.00 mLDosing rateSpeed at which the start v

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭840￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange-2000 ... 2000 mVSelectionoffDefault valueoffTitration rateTitration ra

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭841point for parameterization: Max. rate in mL/min = 0.005 • Expected rateof reaction in µ

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭842￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.8.7.5 STAT U - Titration parametersTab: Method ▶ STAT U ▶ Properties... ▶ Ti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭843Titrando, 855Range0.1 ... 999999 sDefault value2.0 sTitrinoRange1 ... 999999 sDefault v

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭70￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ExamplesTextToTime("2004-12-3 5:22:01 PM";"yMdhmsa") = 200

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭844￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.8.7.6 STAT U - Stop conditionsTab: Method ▶ STAT U ▶ Properties... ▶ Stop co

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭845Last dosingThe stop time starts after the last increment has been dosed, i. e. the stop

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭846￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Monitoring Measured valueMonitoring Measured valueon | off (Default value: off)If t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭847Titrando, 855Range0.0 ... 2000.0 mVDefault value0.2 mVActionSelection of the event to b

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭848￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange0.00 ... 150.00 mL/minDefault value0.00 mL/minLower hysteresisThe lower

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭849Stop command (Titrando, 855)The running STAT command is quit, then the next command is

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭850￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855Range-20.0 ... 150.0 °CDefault value150.0 °CTitrinoRange-170.0 ... 500

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭851Track call on limit exceedingIn this table, which cannot be edited directly, a maximum

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭852￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭853Range1.0 ... 2000.0 mV/mLDefault value25.0 mV/mL5.6.3.8.7.9 STAT U - Additional measur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭712.4.4.7.6 TimeToTextDialog window: Formula editor ▶ Operators/Functi

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭854￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Opens the dialog window External measured value # in which theparameters for t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭855If the activities of the acid and the conjugated base are equal (aA = aB), thenpH=pKa.

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭856￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.9.2 Minimum/Maximum evaluationParameters: Method ▶ DET/MET/SET/KFT/KFC/MEAS

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭8575.6.3.9.4 Gran evaluationParameters: Method ▶ DET/MET ▶ Properties... ▶ Additional eva

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭858￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.3.10 Additional measured values5.6.3.10.1 Calculated measured valueDialog win

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭859Selectionempty | ppm | % | g/L | mg/L | mg/mL | mg/100g | mol/L | mmol/L | mL | g | mg

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭860￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4 Measuring commands5.6.4.1 Measuring commands - OverviewMenu item: Method ▶

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭8615.6.4.2 MEAS pH5.6.4.2.1 MEAS pH - OverviewDialog window: Method ▶ MEAS pH ▶ Properti

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭862￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.BP{x}.TIMTime for the break point x (1…9) in s.BSY Comma

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭863Identification Description.MA.TEMTemperature for the maximum measured value in °C.MA.TI

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭72￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Characters Significance ExampleEWeekday short formMon, Tue, WedEEEEWeekdayMond

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭864￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)If the option not defined is selected as Device name, any device types ordevice gro

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭865offThe temperature will not be measured. The temperature manuallyentered under Temperat

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭866￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measurement with drift controlThe measurement is carried out drift-controlled if th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭867Max. waiting timeIf the signal drift has not yet been reached, then the measured value

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭868￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855, 867Range0 ... 999999 sDefault value120 sTitrinoRange0 ... 9999 sDefa

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭8695.6.4.2.4 MEAS pH - EvaluationsTab: Method ▶ MEAS pH ▶ Properties... ▶ EvaluationsComm

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭870￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Range0.1 ... 20.0 pH/sDefault value1.0 pH/sMaximum evaluationMaximum evaluationon |

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭871WindowA range (window) can be defined on the measured value axis or on the timeaxis. Th

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭872￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Additional calculated measured valuesAdditional calculated measured valueson | off

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭8735.6.4.2.6 MEAS pH - Fix endpoint evaluation Dialog window: Method ▶ MEAS pH ▶ Propert

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭732.4.4.8 Text functions2.4.4.8.1 TextPositionDialog window: Formula

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭874￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ General/HardwareParameters for devices, sensors and stirrers.￭ Measuring paramete

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭875Identification Description.IMEInitial measured value (measured value before startcondit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭876￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)The general parameters for the device, the sensor and the stirrer are definedon thi

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭877SelectionSensor name | pH electrode | Metal electrode |ISE electrodeDefault valueMetal

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭878￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4.3.3 MEAS U - Measuring parametersTab: Method ▶ MEAS U ▶ Properties... ▶ Meas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭879Titrando, 855, 867Range0.1 ... 999.0 mV/minDefault value10.0 mV/minTitrinoRange0.5 ...

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭880￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop measured valueStops when the preset measured value has been reached since the

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭881offNo stop.TemperatureTemperatureMeasuring temperature which can be entered manually. I

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭882￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window Fix endpoint evaluation # to edit the fixedendp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭883measured value can be evaluated as a break point for a small measured valuerange.Range0

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭VII5.5 Tracks ...

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭74￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)2.4.4.8.2 SubTextDialog window: Formula editor ▶ Operators/FunctionsSyntaxy =

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭884￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = TimeRange1 ... 999999 sDefault value999999 s5.6.4.3.5 MEAS U - Additional

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭885[New]Opens the dialog window External measured value # in which theparameters for the e

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭886￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando: 808, 809, 835, 836, 841, 852, 857, 888, 890, 901, 904, 905,906, 907Titrin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭887Identification Description.ETEEnd temperature (temperature following processing ofthe c

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭888￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.STYType of stop with which the command was stopped:1 = n

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭889851, 855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelect

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭890￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)automaticIf a temperature sensor is connected then the temperature will be meas-ure

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭891SelectionMeasurement with drift control | Measurementwithout drift controlDefault value

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭892￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Titrando, 855, 867Range0 ... 999999 sDefault value0 sMax. waiting timeIf the signal

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭893Measuring timeMaximum period of time for measurement.Titrando, 855, 867Range0 ... 99999

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭75ParametersTextThe parameter can be indicated either directly or as a

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭894￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TitrinoRange-170.0 ... 500 °CDefault value25.0 °C5.6.4.4.4 MEAS Ipol - Evaluations

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭895Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enab

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭896￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SlopeMinimum difference between the slope before and after the break point.The smal

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭8975.6.4.4.5 MEAS Ipol - Additional measured valuesTab: Method ▶ MEAS Ipol ▶ Properties..

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭898￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Opens the dialog window External measured value # in which theparameters for t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭899Titrando: 808, 809, 835, 836, 841, 852, 857, 888, 890, 901, 904, 905,906, 907Titrino: 7

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭900￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.ETEEnd temperature (temperature following processing oft

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭901Identification Description.STYType of stop with which the command was stopped:1 = norma

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭902￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)851, 855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭903automaticIf a temperature sensor is connected then the temperature will be meas-ured co

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭76￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)the type Text, Number or Date/Time. Entire operations can also be trans-ferred

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭904￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SelectionMeasurement with drift control | Measurementwithout drift controlDefault v

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭905Titrando, 855, 867Range0 ... 999999 sDefault value0 sMax. waiting timeIf the signal dri

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭906￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measuring timeMaximum period of time for measurement.Titrando, 855, 867Range0 ... 9

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭907TitrinoRange-170.0 ... 500 °CDefault value25.0 °C5.6.4.5.4 MEAS Upol - EvaluationsTab:

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭908￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Threshold valueThe evaluation of the minimum begins as soon as the slope of the cur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭909SlopeMinimum difference between the slope before and after the break point.The smaller

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭910￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4.5.5 MEAS Upol - Additional measured valuesTab: Method ▶ MEAS Upol ▶ Properti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭911[New]Opens the dialog window External measured value # in which theparameters for the e

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭912￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Robotic Titrosampler: 855Conductometer: 856AppearanceThe command has the following

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭913Identification Description.ETEEnd temperature (temperature following processing ofthe c

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭77ExamplesError('RS.IntermediateRes') = 0: the intermediate r

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭914￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.NMPNumber of measuring points in the measuring point lis

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭915851, 855Selection1Default value1TitrinoSelection1 | 2 | diff.Default value1SensorSelect

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭916￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4.6.3 MEAS T - Measuring parametersTab: Method ▶ MEAS T ▶ Properties... ▶ Meas

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭917Titrando, 855, 867Range0.1 ... 999.0 °CDefault value0.5 °CTitrinoRange0.5 ... 999.0 °CD

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭918￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Stop meas. valueStops when the preset measured value has been reached since the sta

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭919offNo stop.TemperatureTemperatureMeasuring temperature which can be entered manually. I

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭920￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[Properties]Opens the dialog window Fix endpoint evaluation # to edit the fixedendp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭921EP criterionMeasure of the minimum sharpness of the break point. The smaller the EPcrit

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭922￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Window = Measured valueRange-20.0 ... 150.0 °CDefault value150.0 °CWindow = TimeRan

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭923Additional external measured valuesAdditional external measured valueson | off (Default

2.4 Formula editor￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭78￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ASCII value(dec)Characters ASCII value(dec)Characters ASCII value(dec)Characte

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭924￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4.7 MEAS T/Flow5.6.4.7.1 MEAS T/Flow - OverviewDialog window: Method ▶ MEAS T

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭925Identifica-tionDescription.EGFLast measured gas flow rate (measured value followingproc

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭926￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifica-tionDescription.MI.TIMTime for the minimum measured value in s.MN.MEAAve

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9275.6.4.7.3 MEAS T/Flow - Measuring parametersTab: Method ▶ MEAS T/Flow ▶ Properties...

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭928￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Threshold valueThe evaluation of the minimum begins as soon as the slope of the cur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭929[Properties]Opens the dialog window Calc. measured value # in which the parame-ters for

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭930￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)ParametersThe parameters for the command MEAS Conc are configured on the fol-lowing

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭931Identifica-tionDescription.LP.CAxCalculated value × (1...3) for the last measuring poin

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭932￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Device typeDisplay or selection of the device type. If a device is selected under D

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭933offThe temperature will not be measured. The temperature entered man-ually under Temper

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭79ExamplesMolecular for-mulaMolar massH2SO498.0734Ca(OH)274.09268AlCl3*

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭934￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Measurement with drift controlThe measurement is carried out drift-controlled if th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭935Range0 ... 999999 sDefault value52 sMeasuring intervalTime interval for entering a meas

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭936￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)TemperatureTemperatureManually entered titration temperature. If a temperature sens

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭937Additional external measured valuesAdditional external measured valueson | off (Default

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭938￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ Measuring parametersParameters for setting the measurement procedure.￭ Evaluation

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭939Identification Description.ITEInitial temperature (temperature before start conditionsa

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭940￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.TC.C3Coefficient c3 of the Chebyshev polynomial of the s

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭941Temperature measurementType of temperature measurement856Selectioncontinuous | automati

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭942￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4.9.3 MEAS Cond - Measuring parametersTab: Method ▶ MEAS Cond ▶ Properties...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭943NoteA constant measured value is often only achieved after a certain time, asmixing and

2.5 Editing￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭80￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Copy selected text to the clipboard.Paste text from the clipboard.Open editor for ent

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭944￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)856Range0.1 ... 999999.0 sDefault value2.0 sStop meas. valueStops when the preset m

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭945offNo stop.TemperatureMeasurement temperatureTemperature of the solution to be measured

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭946￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Sample solutionSelection of the sample solution from the table Sample solutions (TC

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭947Minimum evaluationMinimum evaluationon | off (Default value: off)If this option is enab

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭948￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)SlopeMinimum difference between the slope before and after the break point.The smal

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9495.6.4.9.5 MEAS Cond - Additional measured valuesTab: Method ▶ Commands ▶ MEAS Cond ▶ P

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭950￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)[New]Opens the dialog window External measured value # in which theparameters for t

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭951ParametersThe parameters for the command MEAS TC Cond are configured on thefollowing tw

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭952￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identification Description.FP{x}.TIMTime in s until the fix endpoint × (1…9) is rea

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭953Identification Description.TC.C3Coefficient c3 of the Chebyshev polynomial of the sol-u

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 General program functionstiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭812.5.3 HyperlinkDialog window: HyperlinkThe dialog window Hyperlink s

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭954￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)StirrerThis section is visible only if the 856 Conductivity Module was selected asd

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭955Range0 ... 999999 sDefault value3000 sMeasuring intervalTime interval for entering a me

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭956￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Additional calculated measured valuesAdditional calculated measured valueson | off

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9575.6.4.11 MEAS Ref5.6.4.11.1 MEAS Ref - OverviewDialog window: Method ▶ MEAS Ref ▶ Pro

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭958￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)5.6.4.11.2 MEAS Ref - General/HardwareTab: Method ▶ MEAS Ref ▶ Properties... ▶ Gen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭959End wavelengthUpper limit of the spectrum.Range200.0 ... 1100.0 nmDefault value1000.0 n

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭960￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)￭ General/HardwareParameters for device.￭ Measuring parametersParameters for settin

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9615.6.4.12.2 MEAS Spec - General/HardwareTab: Method ▶ MEAS Spec ▶ Properties... ▶ Gener

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭962￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)End wavelengthUpper limit of the spectrum.Range200.0 ... 1100.0 nmDefault value1000

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9635.6.4.12.5 MEAS Spec - Evaluation window Dialog window: Method ▶ MEAS Spec ▶ Propertie

3.1 Workplace - General￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭82￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)3 Workplace3.1 Workplace - General 3.1.1 Workplace - DefinitionProgram

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭964￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Command variablesThe following command variables are generated in the method run by

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭965Identification Description.LP.MEAMeasured value for the last measuring point in themeas

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭966￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DeviceDevice nameSelection of a device from those available in the device table. Th

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭967Range1 ... 10000 Default value10 SmoothingNumber of neighboring pixels with which the l

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭968￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Fix endpoint evaluationFix endpoint evaluationon | off (Default value: off)If this

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭969Threshold valueThe evaluation of the maximum begins as soon as the slope of the curveex

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭970￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Time for the lower limit of the window.Window = Measured valueRange0 ... 4000 mAUDe

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭9715.6.4.14 STDADD man5.6.4.14.1 STDADD man - OverviewDialog window: Method ▶ STDADD man

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭972￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Identifi-cationDescription.BSY Command status; 1 = BUSY, HOLD or ERROR; 0 =READY; i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭973DeviceDevice nameSelection of a device from those available in the device table. The on

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 Workplacetiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭83￭ ToolsManual control, run test, sample tables, sample assignment tables, texttemplat

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭974￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)Selectioncontinuous | automatic | offDefault valueautomaticcontinuousA temperature

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭975Number of additionsNumber of times the standard solution is to be added.Range1 ... 19 D

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭976￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)DeviceConcentration unit of addition solution.Selectionmol/L | mmol/L | µmol/L | pp

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭977Measuring intervalTime interval for entering a measuring point in the measuring point l

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭978￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)pH/Ion - Meter: 867Robotic Titrosampler: 855AppearanceThe command has the following

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭979Identifi-cationDescription.ENPElectrode zero point calculated from the calibration.ETEE

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭980￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)not definedIn this case, the device name must be assigned by the user at the start

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭981NoteIf an existing solution is selected as the solution to be added then theConcentrati

5.6 Commands￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭982￭￭￭￭￭￭￭￭tiamo 2.1 (ProcessLab)StirrerStirrerSelection of the stirrer.Selection1 | 2 | 3 | 4 | offDefault value1of

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Methodtiamo 2.1 (ProcessLab)￭￭￭￭￭￭￭￭983Addition modeSelectionFixed volume increments | Variable volumeincrementsDefault valueF